BTW, DOWNLOAD part of SurePassExams SRAN-Radio-Network-Performance-Optimization dumps from Cloud Storage: https://drive.google.com/open?id=1OTKORLZK9c-G0J5_IQvUWAWLdtV9SzJS
Are you still staying up for the SRAN-Radio-Network-Performance-Optimization exam day and night? If your answer is yes, then you may wish to try our SRAN-Radio-Network-Performance-Optimization exam materials. We are professional not only on the content that contains the most accurate and useful information, but also on the after-sales services that provide the quickest and most efficient assistants. With our SRAN-Radio-Network-Performance-Optimization practice torrent for 20 to 30 hours, we can claim that you are ready to take part in your SRAN-Radio-Network-Performance-Optimization exam and will achieve your expected scores.
| Section | Objectives |
|---|---|
| RF Optimization Principles | - Coverage and capacity optimization
|
| LTE/NR Performance Optimization | - Optimization techniques
|
| Troubleshooting and Performance Analysis | - Network issue identification and resolution
|
| SRAN Architecture Overview | - SRAN network structure and components
|
| Radio Network Performance Fundamentals | - Key performance indicators (KPIs)
|
>> SRAN-Radio-Network-Performance-Optimization Learning Engine <<
With the rapid development of society, people pay more and more attention to knowledge and skills. So every year a large number of people take SRAN-Radio-Network-Performance-Optimization tests to prove their abilities. But even the best people fail sometimes. In addition to the lack of effort, may also not make the right choice. A good choice can make one work twice the result with half the effort, and our SRAN-Radio-Network-Performance-Optimization Study Materials will be your right choice.
NEW QUESTION # 30
Which of the following statements does not apply to mmWave radio propagation ?
Answer: D
Explanation:
The correct answer is C .
At mmWave / FR2 frequencies , radio propagation is more challenging than in low-band or mid-band spectrum. Diffraction becomes weaker, blockage is more severe, foliage attenuation is high, and building penetration loss is significant. This is why mmWave networks usually require dense site grids, line-of-sight or near-line-of-sight paths, and strong beamforming. Industry mmWave references consistently describe high path loss, high penetration loss, and the need for directional antenna systems to compensate for these losses.
Option C does not apply because water absorption and atmospheric absorption generally become more relevant at higher frequencies, not lower. Rain, humidity, and oxygen/water-vapor absorption are important considerations for mmWave link budgets.
So the statement that does not apply to mmWave propagation is:
Low water absorption at high frequencies.
NEW QUESTION # 31
Single Network Slice Selection Assistance Information , or S-NSSAI , identifies a network slice. Which of the following statements are correct regarding NSSAI ? Refer to the diagram for basic information.
Answer: C
Explanation:
The correct answer is D: A, B, C, and D .
In 5G network slicing, S-NSSAI identifies a single network slice. It is composed of:
SST , or Slice/Service Type
SD , or Slice Differentiator
Statement A is correct.
The combination of SST + SD can uniquely identify a slice. For example, two slices may both use SST 1 for eMBB/MBB-type service, but different SD values can separate them for different enterprises, tenants, or service groups.
Statement B is correct.
SST is mandatory. It is an 8-bit numeric field that indicates the expected slice/service behavior, such as eMBB, URLLC, or mMTC.
Statement C is correct.
SD is optional. It is a 24-bit field used to differentiate multiple slices that may share the same SST.
Statement D is correct.
SST may use standardized values, such as SST 1 for eMBB, SST 2 for URLLC, and SST 3 for mMTC/MIoT.
It may also use operator-specific or non-standardized values depending on deployment requirements.
NEW QUESTION # 32
At which mark are all conditions fulfilled for energy saving , so the cell will be switched off? Refer to the image below.
Answer: C
Explanation:
The correct answer is B , which corresponds to mark C in the diagram.
In the diagram, the energy-saving process follows these stages:
Before mark B , the cell is entering the power-saving period, but the required load condition has not yet been satisfied for the required duration.
At mark B , the measured load has gone below the configured threshold, but the cell is not switched off immediately. The system must confirm that the load remains below the required threshold for the configured time.
At mark C , the load has stayed below the required threshold for the required duration, shown as 5 minutes in the diagram. At this point, all conditions are fulfilled, and the cell can be switched off. The diagram also shows the state becoming:
energySavingState = energySaving
Marks D and E are already inside or near the later part of the power-saving period. Mark E is associated with operator suspension/exit behavior, not the initial moment when all switch-off conditions are first fulfilled.
NEW QUESTION # 33
When selecting an LTE anchor layer for EN-DC , why is it important to check 3GPP band combinations ?
Answer: C
Explanation:
The correct answer is B .
In 5G NSA EN-DC , the UE connects to LTE as the Master Cell Group , or anchor, and NR as the Secondary Cell Group . Not every LTE band can be paired with every NR band. The supported LTE-NR combinations are defined by 3GPP band-combination rules and must also be supported by the UE chipset and device capability.
For example, an operator may have LTE Band 3, Band 7, or Band 20 and NR n78, but only certain LTE-NR combinations may be valid for EN-DC. If the selected LTE anchor band is not supported in combination with the NR band, the UE will not be able to establish EN-DC even if LTE and NR coverage both exist.
Option C is not correct because dual-uplink support depends on UE capability and specific band-combination support; it cannot be guaranteed for all UE models. Option A and D are unrelated to the main purpose of checking 3GPP band combinations.
So the correct reason is:
To ensure that LTE and NR bands are compatible and allowed as EN-DC pairs.
NEW QUESTION # 34
In the case of 5G SA, which of the following triggers the Radio Link Failure, or RLF, handling mechanism?
Answer: B
Explanation:
The correct answer is C.
In 5G SA, Radio Link Failure handling is mainly UE-driven. The UE monitors the radio link quality using lower-layer indications such as in-sync and out-of-sync indications. If the UE receives enough out-of-sync indications, it starts the relevant RLF timer, commonly associated with T310 behavior. If the link does not recover before the timer expires, the UE declares Radio Link Failure and starts recovery, such as RRC re- establishment.
The gNodeB can detect uplink problems and may release or reconfigure the UE, but the classical RLF handling mechanism is triggered at the UE side.
So the correct answer is:
UE indication timer only.
NEW QUESTION # 35
......
Nokia SRAN-Radio-Network-Performance-Optimization exam is an popular examination of the IT industry, and it is also very important. We prepare the best study guide and the best online service specifically for IT professionals to provide a shortcut. SurePassExams Nokia SRAN-Radio-Network-Performance-Optimization Exam covers all the content of the examination and answers you need to know. Tried Exams ot SurePassExams, you know this is something you do everything possible to want, and it is really perfect for the exam preparation.
SRAN-Radio-Network-Performance-Optimization Exam Dump: https://www.surepassexams.com/SRAN-Radio-Network-Performance-Optimization-exam-bootcamp.html
2026 Latest SurePassExams SRAN-Radio-Network-Performance-Optimization PDF Dumps and SRAN-Radio-Network-Performance-Optimization Exam Engine Free Share: https://drive.google.com/open?id=1OTKORLZK9c-G0J5_IQvUWAWLdtV9SzJS