We hope that our 300-110 exam software can meet all your expectations including the comprehensiveness and authority of questions, and the diversity version of materials - showing three versions of 300-110 exam materials such as the PDF version, the online version and the simulation test version. Our intimate service such as the free trial demo before purchased and the one-year free update service of our 300-110 after you have purchased both show our honest efforts to you.
| Section | Weight | Objectives |
|---|---|---|
| WLAN High Availability and Security Design | 20% | - Management and monitoring design - Security architecture design
|
| Wireless Site Survey | 25% | - RF propagation and attenuation analysis - Pre-deployment survey and validation - Design requirements collection and constraint evaluation
|
| Mobility Design | 25% | - Roaming optimization
|
| Wireless Infrastructure Design | 30% | - Wired-wireless integration design
|
300-110 practice exam will provide you with wholehearted service throughout your entire learning process. This means that unlike other products, the end of your payment means the end of the entire transaction our 300-110 learning materials will provide you with perfect services until you have successfully passed the 300-110 Exam. And if you have any questions, just feel free to us and we will give you advice on 300-110 study guide as soon as possible.
NEW QUESTION # 55
A company has three Cisco WLCs that are joined as a mobility group. Mobility multicast messaging is enabled. All the WLCs in the mobility group communicate via a multicast. Which configuration must be identical between the three WLCs to validate communication?
Answer: C
NEW QUESTION # 56
A customer has a single anchor WLC named Anchor A. Anchor A is in a DMZ and provides guest access.
The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?
Answer: C
Explanation:
In a wireless network design where anchor redundancy is required for guest access, setting different priorities for the anchor controllers ensures deterministic primary and backup behavior. Cisco anchor priority uses a lower numerical value to indicate higher preference - Priority 1 is the highest priority (most preferred) anchor, and Priority 3 is lower priority. Setting Anchor A to priority 1 (Option D) makes it the primary anchor controller - all new guest client sessions will preferentially anchor to Anchor A. Setting Anchor B to priority
3 makes it the standby anchor - guest clients will only be anchored to Anchor B when Anchor A is unavailable. This creates a clear primary/backup relationship with deterministic failover. Setting both anchors to the same priority (Options A and C) would result in load balancing between the two anchors rather than active/standby behavior. Option B incorrectly reverses the priorities, making Anchor B the primary and Anchor A the backup. Reference: WLSD Study Guide - Guest Anchor Redundancy Design, Anchor Priority Configuration, DMZ Anchor WLC Architecture.
NEW QUESTION # 57
An engineer must identify the network requirements for a company that has a main office and 10 branch offices. The network must be able to support data, voice, video, and location tracking.
Which two factors must be considered? (Choose two.)
Answer: A,B
Explanation:
When designing a wireless network to support diverse services -- including data, voice, video, and location tracking -- across a distributed enterprise with a main office and 10 branch locations, the two primary design factors directly shaping the RF and capacity architecture are the number of wireless devices requiring access and the type of site where the survey will be performed. The device count (Option B) drives AP density, channel reuse planning, capacity modeling, and controller licensing requirements. Each service type -- particularly VoWLAN and video -- imposes strict per- client throughput and latency constraints that must be multiplied across the concurrent device population. The type of site (Option C) determines the survey approach, attenuation characteristics, coverage requirements, and antenna selection. A warehouse, hospital, or open- plan office each demands a fundamentally different RF design.
NEW QUESTION # 58
An enterprise is using wireless as the main network connectivity for clients. To ensure wireless network availability, two standalone controllers are installed in the head office. APs are connected to the controllers using a round-robin approach to load balance the traffic. After a power cut, the wireless clients disconnect while roaming. An engineer tried eping from the controller but fails. Which protocol needs to be allowed between the networks that the controllers are installed?
Answer: A
Explanation:
When eping (EoIP ping) fails between two Cisco Wireless LAN Controllers, it indicates that the data path of the mobility tunnel is blocked. In Cisco AireOS wireless networks, the mobility data path uses IP Protocol 97 (EtherIP - Ethernet-over-IP encapsulation) for tunneling client traffic between the anchor and foreign controllers. This is distinct from the control path, which uses UDP port 16666. When the mobility data path (IP Protocol 97) is blocked by a firewall or ACL between the two controllers ' networks, eping will fail because eping specifically tests the EoIP data encapsulation path. After a power cut, when clients disconnect and attempt to roam between APs on different controllers, the mobility tunnel must be operational for session continuity. If IP Protocol 97 is blocked, the mobility data plane cannot function, causing client disconnections during inter-controller roaming events. The other IP protocols listed (67, 77, 87) are not used for Cisco WLC mobility tunneling. Reference: WLSD Study Guide - Mobility Tunnel Data Path, IP Protocol 97 (EtherIP), eping Command and Troubleshooting.
NEW QUESTION # 59
An engineer must perform a predictive wireless survey to indicate the number of access points required. The engineer has created a new project and imported the floor plan. Which step must be taken next for accurate AP placement?
Answer: B
Explanation:
After creating a new predictive survey project and importing the floor plan, the next mandatory step is to set the scale of the floor plan. Setting the scale is critical because all subsequent measurements - AP coverage radius, cell overlap calculations, and distance-based attenuation modeling - depend on the accuracy of the floor plan ' s physical dimensions. If the scale is incorrect, the predictive model will place APs at incorrect distances relative to each other and produce inaccurate coverage predictions. The scale is typically set by the engineer clicking on two known points on the floor plan and entering the real-world distance between them, calibrating the software ' s measurement system. Analyzing the network (Option A) and placing APs (Option C) come after the scale is established. Identifying the coverage area (Option B) is often done simultaneously with scale setting or immediately after. Setting the scale first ensures all subsequent work is based on accurate physical dimensions. Reference: WLSD Study Guide - Ekahau Predictive Survey Workflow, Floor Plan Import and Scale Setting, Pre-Deployment Survey Methodology.
NEW QUESTION # 60
......
Many users report to us that they are very fond of writing their own notes while they are learning. This will enhance their memory and make it easier to review. Our 300-110 exam questions have created a PDF version of the 300-110 practice material to meet the needs of this group of users. You can print the PDF version of the 300-110 learning guide so that you can carry it with you. As long as you have time, you can take it out to read and write your own experience.
Valid Exam 300-110 Blueprint: https://www.dumpexam.com/300-110-valid-torrent.html