2026 Latest ExamDiscuss NSE5_FSW_AD-7.6 PDF Dumps and NSE5_FSW_AD-7.6 Exam Engine Free Share: https://drive.google.com/open?id=1ie7e_jg8SJcm7Ps7_e2lqYz5oXz2B4Jz
Whole ExamDiscuss's pertinence exercises about Fortinet certification NSE5_FSW_AD-7.6 exam is very popular. ExamDiscuss's training materials can not only let you obtain IT expertise knowledge and a lot of related experience, but also make you be well prepared for the exam. Although Fortinet Certification NSE5_FSW_AD-7.6 Exam is difficult, through doing ExamDiscuss's exercises you will be very confident for the exam. Be assured to choose ExamDiscuss efficient exercises right now, and you will do a full preparation for Fortinet certification NSE5_FSW_AD-7.6 exam.
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
>> NSE5_FSW_AD-7.6 Exam Cost <<
The ExamDiscuss wants to win the trust of Fortinet NSE 5 - FortiSwitch 7.6 Administrator NSE5_FSW_AD-7.6 exam candidates at any cost. To achieve this objective the ExamDiscuss is offering NSE5_FSW_AD-7.6 exam passing money-back guarantee. Now your investment with ExamDiscuss is secured from any risk. If you fail the Fortinet NSE 5 - FortiSwitch 7.6 Administrator NSE5_FSW_AD-7.6 Exam despite using PMI Dumps, you can claim your paid amount. Thanks and best of luck in your exam and career!
NEW QUESTION # 10
Refer to the diagnostic output:
Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?
Answer: B
Explanation:
The MAC address " 00:50:56:96:e3:fc " appearing in two different VLANs (4089 and 4094) in the diagnostic output indicates it is a MAC address associated with a device that supports traffic from multiple VLANs.
Such a behavior is typical of network infrastructure devices like switches or routers, which are configured to allow traffic from various VLANs to pass through a single physical or logical interface. This is essential in network designs that utilize VLANs to segregate network traffic for different departments or use cases while using the same physical infrastructure.
References:
For more detailed information on MAC table diagnostics and VLAN configurations in FortiGate devices, refer to the official Fortinet documentation:Fortinet Product Documentation.
NEW QUESTION # 11
Refer to the exhibit.
PC1 and PC2 are connected to port1 on FortiSwitch. Which VLAN tags will FortiSwitch apply when forwarding PC1 and PC2 traffic out of port2? (Choose one answer)
Answer: A
Explanation:
According to theFortiSwitchOS 7.6 Administration Guideand theFortiSwitch 7.6 Study Guide, the classification of untagged traffic entering a switch port is determined by the port's hierarchy of VLAN assignment rules.
For the traffic arriving atport1:
* PC1 (MAC 58:ef:68:b4:33:32):The exhibit shows an explicitMAC-based VLAN assignmentrule for this specific MAC address, placing it intoVLAN 10. In FortiSwitchOS, dynamic assignments like MAC-based or protocol-based rules take precedence over the port's static native VLAN. Therefore, PC1's traffic is internally associated with VLAN 10.
* PC2 (MAC 58:ef:68:b4:33:c3):There is no MAC-based rule for this device. As a result, the switch falls back to the default behavior and assigns the traffic to the port'sNative VLAN, which isVLAN 20.
For the traffic exiting port2:
The egress behavior depends on the VLAN tagging configuration of the outgoing interface. On port2, the Native VLAN is 4094, and VLANs 10 and 20 are listed as Allowed VLANs. According to Fortinet documentation, any traffic belonging to an allowed VLAN that does not match the native VLAN ID of the egress port must be sent as tagged 802.1Q frames. Since neither VLAN 10 nor VLAN 20 matches the native ID of 4094, the FortiSwitch will apply a VLAN 10 tag to PC1's traffic and a VLAN 20 tag to PC2's traffic as they are forwarded to the FortiGate.
NEW QUESTION # 12
Which two are valid traffic processing actions that a FortiSwitch access control list (ACL) can apply to matching traffic? (Choose two answers)
Answer: B,D
Explanation:
According to theFortiSwitchOS 7.6 Administration Guideand theNSE 5 FortiSwitch Study Guide, Access Control Lists (ACLs) are used to provide granular control over the traffic entering or leaving a switch port.
ACLs function by definingclassifiers(to match specific traffic based on criteria like MAC address, IP address, or VLAN ID) and then applying specificactionsto that matched traffic.
The documentation explicitly categorizes ACL actions into three distinct groups:
* Traffic Processing:This category includes actions that dictate the physical handling of the frame. Valid actions listed in the official documents under this header includecount(to track packet volume),drop(to block the traffic),redirect(to forward the frame to a specific physical port or interface instead of its original destination), andmirror(to send a copy to a monitoring port).
* Quality of Service (QoS):This category focuses on traffic prioritization and bandwidth management. It includes actions such asrate limiting,remarking CoS/DSCP values, andsetting the egress queue(e.g., assigning a packet to a specific queue number from 0 to 7).
* VLAN:This allows for modifications such as setting anouter VLAN tagon frames.
The question specifically asks for "traffic processing actions." Based on the 7.6 documentation,Redirect frames to another port(Option A) andDrop frames(Option D) are explicitly defined under the "Traffic Processing" action header. While "Assign traffic to a high-priority egress queue" (Option B) is a valid action an ACL can perform, it is technically categorized as aQoS action, not a traffic processing action.Encrypt frames(Option C) is not a supported ACL action on FortiSwitch hardware, as encryption is typically handled at higher layers or via dedicated MACsec configurations on specific models.
NEW QUESTION # 13
(Full question statement start from here)
Refer to the exhibit.
You run the command diagnose switch-controller switch-info loopguard access-1 and see that theMAC-Move column displays a value of0forport1.
What does this indicate? (Choose one answer)
Answer: A
Explanation:
In FortiSwitchOS 7.6,Loop Guardis a Layer 2 loop detection mechanism primarily designed to protect access ports from unintended network loops. In itsoriginal implementation, Loop Guard only detected loops on the native VLAN, which limited its effectiveness in environments using multiple tagged VLANs. To address this limitation, Fortinet enhanced Loop Guard by introducing theMAC move detection feature, as documented in the FortiSwitchOS 7.6 Administrator Guide.
TheMAC move optioninstructs the FortiSwitch to monitor for repeated MAC address flapping events across ports or VLANs. Such MAC movement is a strong indicator of a Layer 2 loop. However, this enhanced detection mechanism isdisabled by defaultand must be explicitly enabled by configuring aMAC move threshold greater than zero.
According to the FortiSwitchOS 7.6 Administrator Guide (page 164), enabling MAC move allows Loop Guard to detect loops beyond the native VLAN. Furthermore, the guide explicitly states (page 166) thata MAC-Move value of 0 indicates that the MAC move feature is not enabled. This means the switch is not monitoring MAC address movement as part of its loop detection logic, even though Loop Guard itself may still be enabled on the port.
Therefore, a MAC-Move value of 0 does not indicate that Loop Guard is disabled or inactive, nor does it imply VLAN-wide port shutdown behavior. It strictly confirms thatMAC move detection has not been enabled, makingOption Cthe correct and fully verified answer based on FortiSwitchOS 7.6 documentation.
NEW QUESTION # 14
Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?
Answer: B
Explanation:
Layer 2 flooding caused by Ethernet frames with all bytes in the destination MAC address set to FF refers to broadcast frames.Here's why:
* Broadcast Ethernet Frame (A):
* Address Specification:In Ethernet networking, a broadcast frame has a destination MAC address ofFF:FF:FF:FF:FF:FF, which instructs network devices to forward the frame to all devices within the broadcast domain.
* Network Behavior:This causes Layer 2 flooding as the frame is sent to all ports in the VLAN, except the originating port, ensuring that the broadcast reaches all network segments.
* Other Frame Types:
* Unicast (B)targets a single device.
* Multicast (C)targets a group of devices.
* Anycast (D)is not used in Ethernet but rather in IP-based routing to route to the nearest of multiple destinations, typically in internet addressing.
References:You can find more information about Ethernet frame types in networking textbooks or documentation that discusses network layer interaction:Network Theory Books
NEW QUESTION # 15
......
Many companies arrange applicants to take certification exams since 1995 internationally such like Microsoft, Fortinet, Veritas, EMC, and HP. Fortinet NSE5_FSW_AD-7.6 exam sample online was produced in 2001 and popular in 2008. So far many companies built long-term cooperation with exam dumps providers. Many failure experiences tell them that purchasing a valid Fortinet NSE5_FSW_AD-7.6 Exam Sample Online is the best effective and money-cost methods to achieve their goal.
New NSE5_FSW_AD-7.6 Test Labs: https://www.examdiscuss.com/Fortinet/exam/NSE5_FSW_AD-7.6/
BTW, DOWNLOAD part of ExamDiscuss NSE5_FSW_AD-7.6 dumps from Cloud Storage: https://drive.google.com/open?id=1ie7e_jg8SJcm7Ps7_e2lqYz5oXz2B4Jz