BONUS!!! Download part of Real4dumps 300-110 dumps for free: https://drive.google.com/open?id=1_2IW3lIXUh-GRh-laulg7YymtBlu9wRl
If you visit our website Real4dumps, then you will find that our Cisco 300-110 practice questions are written in three different versions: PDF version, Soft version and APP version. All types of 300-110 Training Questions are priced favorably on your wishes. Obtaining our Cisco 300-110 study guide in the palm of your hand, you can achieve a higher rate of success.
| Section | Weight | Objectives |
|---|---|---|
| Mobility Design | 25% | - Roaming optimization
- Mobility architecture models
|
| Wireless Site Survey | 25% | - Layer 1 site survey execution and analysis - Design requirements collection and constraint evaluation
- RF propagation and attenuation analysis |
| WLAN High Availability and Security Design | 20% | - Security architecture design
|
| Wireless Infrastructure Design | 30% | - High-density wireless design
|
>> Latest Cisco 300-110 Learning Materials <<
Real4dumps offers actual and updated 300-110 Dumps after seeing the students struggling to prepare quickly for the test. We have made this product after consulting with a lot of professionals so the students can be successful. Real4dumps has hired a team of professionals who work on a daily basis without caring about themselves to update the Cisco 300-110 practice material.
NEW QUESTION # 92
An engineer is designing a high-density WLAN and wants to reduce the airtime consumed by each client transmission. Which configuration should be included in the RF profile?
Answer: C
Explanation:
A frame transmitted at a low data rate occupies the channel far longer than the same frame sent at a high rate, and because the medium is shared, a single distant client transmitting at 1 Mbps consumes airtime that every other client on that channel must wait through. Disabling the low rates and raising the mandatory minimum forces clients to either connect at an efficient rate or roam to a closer AP, which shrinks the effective cell size, reduces co-channel interference, and increases aggregate capacity - all of which are desirable in a dense design where APs are closely spaced. Management and broadcast frames are also sent at the lowest mandatory rate, so raising that floor reduces beacon and broadcast overhead as well. Leaving all rates enabled or setting 1 Mbps as mandatory produces oversized cells with heavy airtime consumption, and restricting the 2.4 GHz radio to 802.11b rates would be the worst possible outcome for efficiency.
NEW QUESTION # 93
Which profile is included within a site tag when configured in a Cisco 9800 WLC architecture?
Answer: C
Explanation:
The Cisco Catalyst 9800 IOS XE WLC uses a tag-based configuration architecture. Three primary tag types are used: site tags, policy tags, and RF tags. The site tag associates an AP with its operational context and contains two specific profile references: the AP join profile (defining AP-level parameters such as NTP, syslog, SSH, LED behavior, and CAPWAP timers) and the flex profile (defining FlexConnect-specific parameters including locally switched VLANs, split tunneling, local authentication settings, and VLAN-ACL mappings). The flex profile within the site tag enables the AP to operate in FlexConnect mode with locally configured switching behavior when WLC connectivity is lost.
NEW QUESTION # 94
In an N+1 design, a customer needs certain APs in the emergency department to rejoin the backup controller before all other APs when a failover occurs. Which feature must the engineer include in the design?
Answer: C
Explanation:
AP failover priority allows an engineer to assign each AP a priority level of low, medium, high, or critical. When a backup controller in an N+1 design receives more join requests than its licensed AP capacity allows, it uses these priority values to decide which APs to accept. If the controller is already at capacity and a higher-priority AP requests to join, the controller disassociates a lower- priority AP to make room for it. This makes AP failover priority the correct design element when specific coverage areas - such as an emergency department, operating theater, or warehouse safety zone - must be guaranteed service during a controller outage. AP fallback is a different feature that returns an AP to its primary controller once that controller comes back online, and it does not influence which APs are admitted during the failure. Mobility group priority and join profile weighting are not the mechanisms that govern controller admission during failover.
NEW QUESTION # 95
A network design supports data and voice in 2.4 GHz and 5.0 GHz. The design must support asset tracking without affecting the existing design. Which action must be taken?
Answer: A
Explanation:
Cisco's WLAN location and asset tracking architecture (based on Cisco Spaces or legacy Cisco MSE/CMX) relies on the ability to receive and measure the RF signal from tagged assets at multiple APs simultaneously. For accurate location determination using triangulation or trilateration algorithms, a minimum of three APs must receive the tag's signal with sufficient RSSI.
Monitor mode APs are dedicated to passive RF listening -- they do not transmit client-serving SSIDs and focus their full radio attention on scanning all channels for signal measurement.
Placing monitor mode APs specifically on the perimeter of an asset tracking area provides the spatial diversity and boundary detection capability needed to accurately triangulate assets throughout the interior, without requiring any modifications to the existing data/voice serving APs.
Adding monitor mode APs at the perimeter as an overlay ensures the existing 2.4 GHz and 5 GHz voice/data design is entirely undisturbed.
NEW QUESTION # 96
An engineer must design and configure a wireless network for pervasive coverage in an oil terminal, casual web and email traffic, 5 GHz. What is the best design?
Answer: C
Explanation:
An oil terminal presents specific wireless design constraints: the requirement is pervasive coverage (maximum geographic coverage) for low-bandwidth applications (casual web and email). These requirements prioritize coverage reach over throughput optimization. The correct approach is to keep all data rates enabled, including lower rates such as 6, 9, 12, and 18 Mbps -- because in an industrial environment with challenging RF propagation paths, reflective surfaces, and potential obstructions, lower data rates extend the functional coverage range of each AP.
Web and email traffic does not require high data rates; even 1-6 Mbps is sufficient for these applications. Disabling rates below 54 Mbps (Option A) would dramatically shrink each AP's effective coverage area, requiring many more APs for pervasive coverage and failing the primary design objective. Assigning static maximum power without RRM auto-adjustment creates excessive co-channel interference.
NEW QUESTION # 97
......
With the aim of helping aspirants to achieve the Designing Cisco Wireless Networks (300-110) certification, Real4dumps is committed to providing the best quality and updated Cisco 300-110 exam dumps. With their authentic and Real 300-110 Exam Questions, you can be confident of passing the Cisco 300-110 certification exam on the first try.
Study 300-110 Material: https://www.real4dumps.com/300-110_examcollection.html
DOWNLOAD the newest Real4dumps 300-110 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1_2IW3lIXUh-GRh-laulg7YymtBlu9wRl