Before we start develop a new NSEI_OTS_AR-7.6 real exam, we will prepare a lot of materials. After all, we must ensure that all the questions and answers of the NSEI_OTS_AR-7.6 exam materials are completely correct. First of all, we have collected all relevant reference books. Most of the NSEI_OTS_AR-7.6 Practice Guide is written by the famous experts in the field. And we also add the latest knowledage points into the content of the NSEI_OTS_AR-7.6 learning questions, so that they are always being up to date.
| Section | Objectives |
|---|---|
| Asset Management | - Explain OT standards and Fortinet compliance - Use Fortinet Security Fabric for an OT network - Implement device detection on FortiGate and FortiNAC |
| Network Security | - Configure automation - Configure security inspections for industrial protocols - Configure virtual patching |
| Network Access Control | - Explain OT Ethernet concepts - Configure network segmentation schemas - Configure network access authentication |
| Monitoring and Risk Assessment | - Create FortiAnalyzer event handlers - Perform risk assessment and management - Analyze security reports from FortiAnalyzer |
>> NSEI_OTS_AR-7.6 Valid Test Discount <<
You can try NSEI_OTS_AR-7.6 free demo before you decide to buy the full version practice test. NSEI_OTS_AR-7.6 exam dumps details are researched and produced by our Professional Certification Experts who are constantly using industry experience to produce precise, and logical. Prep4cram NSEI_OTS_AR-7.6 Exam Dumps will not only help you pass in one attempt, but also save your valuable time.
NEW QUESTION # 15
Refer to the exhibit.
Why is the OT View tab not available in the Asset Identity Center section of the FortiGate-1 device? (Choose one answer)
Answer: A
Explanation:
The correct answer is A . The study guide states that "The OT view is not available by default. You must enable it in the Feature Visibility section of the GUI or using the CLI command shown on this slide" and shows config system settings # set gui-ot enable . It also says that "After you enable the feature, the Asset Identity Center contains an Asset Identity List tab and an OT View tab." This directly explains why the OT View tab is missing: the feature that enables the Purdue-style OT display has not been enabled yet.
The OT View is the view that displays devices in a Purdue diagram , and the Asset Identity List also shows the current Purdue level for each device. Because the answer options do not explicitly say enable OT View in Feature Visibility , option A is the intended match, since it refers to enabling the Purdue-related OT display feature. Option B is incorrect because device detection affects visibility of devices, not whether the OT View tab exists. Option C is not supported by the study guide, and option D is also not given as the requirement for showing the OT View tab.
NEW QUESTION # 16
Refer to the exhibit.
An industrial Ethernet protocol skipping layers 3 to 6 is shown. Which industrial Ethernet protocol is it?
(Choose one answer)
Answer: B
Explanation:
The correct answer is D. EtherCAT . The study guide explicitly states under the Ethernet/IP and EtherCAT section that "EtherCAT is a protocol that offers real-time communication in a primary-secondary configuration" and "EtherCAT skips layers 3 to 6 to deliver real-time communication." It also adds that
"the most important feature of this protocol is that secondary devices collect only the information they need from the data packets." This matches the exhibit exactly, where the diagram shows Real-Time Data above a Proprietary MAC and Proprietary physical layer , reflecting the protocol structure that bypasses the intermediate OSI layers.
The other options do not match this behavior. The guide says POWERLINK uses layer 2 and layer 7 of the OSI model, not that it skips layers 3 to 6. It also explains that Ethernet/IP is the industrial protocol based entirely on Ethernet standards and adapts to the OSI model. Modbus is described as an open client/server protocol and is not suitable for transmitting data in real time . Therefore, the protocol in the exhibit is clearly EtherCAT .
NEW QUESTION # 17
Refer to the exhibit.
A partial OT network is shown.
You have recently removed the air gap in the network to provide full connectivity.
What must you configure to protect your OT network from external attacks?
Answer: C
Explanation:
The correct answer is D . Removing the air gap creates connectivity between the OT environment and external networks, significantly increasing exposure to unauthorized access and cyberattacks. Fortinet explains that the expansion of remote connectivity and IT/OT interconnections increases the OT attack surface and that the modern threat landscape requires IPS to block a wider range of threats . In the shown Purdue-style topology, FortiGate_Level5 is positioned at the upper boundary toward external connectivity and is therefore the appropriate enforcement point for protecting against attacks entering from outside the OT environment. Virtual patching at Level 2 is intended primarily to compensate for known vulnerabilities on specific OT devices that cannot yet be patched. Application Control provides industrial protocol visibility and command-level control, while merely enabling OT signatures at Level 3 does not replace perimeter intrusion prevention. Consequently, IPS belongs on FortiGate_Level5 .
NEW QUESTION # 18
Refer to the exhibit.
An automation trigger creation wizard is shown. You want to automate some tasks in your OT network. In a FortiGate device, you create a new automation trigger based on a FortiAnalyzer event handler. When you want to configure the Event handler name field, the event handler created in FortiAnalyzer is not shown.
What are two reasons for this? (Choose two answers)
Answer: A,C
Explanation:
The correct answers are A and B .
Option B is correct because the study guide states that "When a handler generates an event with the automation stitch option enabled, FortiAnalyzer sends a notification" to FortiGate. If Automation Stitch is not enabled in the FortiAnalyzer event handler, that handler will not be usable for the FortiGate automation- stitch workflow. The guide also explains that the configuration of each event handler can include
"Automation stitches" and "Rules," showing that this is a required part of the FortiAnalyzer-to-FortiGate automation path.
Option A is also correct. The study guide explains the automation flow in the Security Fabric:
"FortiAnalyzer parses the logs and notifies the root FortiGate" and then "The root FortiGate triggers the action." That means FortiGate must have the FortiAnalyzer connection configured through the Security Fabric side before it can consume FortiAnalyzer event handlers. The warning in the exhibit about configuring a FortiAnalyzer connection also points directly to that requirement.
Option C is incorrect because + Create is not the reason the existing event handler is missing; it is only an interface control. Option D is not the best answer for this item because the question is about why the event handler name list on FortiGate is empty for FortiAnalyzer-triggered automation. The study guide's verified requirements for that workflow are the FortiAnalyzer-to-FortiGate Fabric connection and enabling Automation Stitch on the FortiAnalyzer event handler.
NEW QUESTION # 19
Refer to the exhibit.
The Core Network Security Connectors page of the FortiGate-2 device is shown. Which statement is correct? (Choose one answer)
Answer: D
Explanation:
Based on the provided exhibit and the OT Security 7.6 Architect curriculum regarding the Fortinet Security Fabric :
* Fabric Role : The exhibit clearly shows that FortiGate-2 has the role set to Join Fabric . This confirms it is a downstream device and not the Fabric Root (eliminating Option A).
* Upstream Connection : The device is configured to point to an Upstream FortiGate at IP address
10.1.2.254 .
* Fabric Status : The status is currently displayed as Not Connected . In a standard Fortinet Security Fabric deployment, once a downstream device is configured to join the fabric, it sends a request to the upstream root device. The root FortiGate must then explicitly authorize the downstream unit before the connection is established and the status changes to " Connected. "
* Authorization Requirement : The " Not Connected " status, while having the upstream IP correctly configured, is the classic indicator that the authorization step is pending on the root FortiGate.
Furthermore, under the LAN Edge Devices section, it shows another downstream FortiGate requiring authorization on this specific unit, highlighting that authorization is a manual security requirement for all stages of the Fabric hierarchy.
* FortiAnalyzer Status : While the Logging & Analytics section shows FortiAnalyzer is Disabled , this is a configuration choice and does not prevent the Security Fabric from connecting; therefore, configuring it is not the solution to the connectivity status shown (eliminating Option C).
In summary, FortiGate-2 cannot join the fabric until an administrator logs into the Root FortiGate (10.1.2.254) and authorizes the join request from FortiGate-2.
NEW QUESTION # 20
......
With our customizable learning experience and self-assessment features of practice exam software for NSEI_OTS_AR-7.6 exam, you will be able to know your strengths and areas of improvement. We provide authentic braindumps for NSEI_OTS_AR-7.6 certification exam. In fact, we guarantee that you will pass the NSEI_OTS_AR-7.6 Certification Exam on your very first try. If we fail to deliver this promise, we will give your money back! Aside from providing you with the most reliable dumps for NSEI_OTS_AR-7.6, we also offer our friendly customer support staff. They will be with you every step of the way.
Reliable Exam NSEI_OTS_AR-7.6 Pass4sure: https://www.prep4cram.com/NSEI_OTS_AR-7.6_exam-questions.html