P.S. Free & New JN0-481 dumps are available on Google Drive shared by PracticeDump: https://drive.google.com/open?id=1ZtpCHiR3VViO8g7JUoGPTS9y4HEfYmbg
Our Juniper JN0-481 demo products hold the demonstration for our actual products, demos are offered at no cost only for raising your confidence level. Procure the quality of our product in advance, unsighted featured becomes reveal with our JN0-481 Demo products. Free Private Cloud Monitoring and Operations with demos respond to all kind of worries that customers have in their mind while going for actual purchase.
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
All knowledge contained in our JN0-481 Practice Engine is correct. Our workers have checked for many times. Also, we will accept annual inspection of our JN0-481 exam simulation from authority. The results show that our JN0-481 study materials completely have no problem. Our company is rated as outstanding enterprise. And at the same time, our website have became a famous brand in the market. We also find that a lot of the fake websites are imitating our website, so you have to be careful.
NEW QUESTION # 58
The analytics probe shown in the exhibit is enabled.
The ge-0/0/5 interface on the my-esl-001-leaf1 node receives an average of greater than 1 Mbps of traffic. Which two statements are correct in this scenario? (Choose two.)
Answer: A,D
Explanation:
In Apstra 5.1, an IBA probe is a defined analytics pipeline that applies to a scoped set of graph objects (here, interfaces) and evaluates telemetry against logic defined in its processors. The exhibit shows a probe that consumes Interface Counters Average and then applies a Range processor. In the processor configuration, the Anomalous Range is set to "greater than 1,000,000" (bytes per second-equivalent for ~1 Mbps depending on the probe's metric definition), and Raise Anomaly is set to True. Therefore, when ge-0/0/5 receives an average traffic level above the configured threshold, the probe's condition evaluates as anomalous and Apstra raises a probe anomaly for that interface. That makes statement A correct.
When probe anomalies are raised, Apstra surfaces them in the blueprint's Analytics area because they are analytics-derived findings (as opposed to configuration drift or deployment workflow issues). As a result, the blueprint's Analytics tab indicator changes state (commonly to red with a badge count) to signal active analytics anomalies requiring attention. That makes statement B correct.
This event is not classified as a service anomaly (which is associated with higher-level service intent/assurance objects) unless separately mapped by policy/logic, and it does not primarily drive the Active tab indicator, which is focused on operational state views rather than being the primary alert surface for IBA probe anomalies.
NEW QUESTION # 59
You are installing a Juniper Apstra server in your data center. You have multiple users that will be expected to configure, manage, and carry out operational tasks in your data center. You have decided to implement remote user authentication for the role-based access control of your Apstra server. In this scenario, which three methods are supported? (Choose three.)
Answer: A,B,E
Explanation:
To implement remote user authentication for the role-based access control of your Apstra server, you can use one of the following methods: TACACS+, LDAP, or RADIUS. These are the protocols that Juniper Apstra supports to authenticate and authorize users based on roles assigned to individual users within an enterprise. You can configure the Apstra server to use one or more of these protocols as the authentication sources and specify the order of preference. You can also configure the Apstra server to use local user accounts as a fallback option if the remote authentication fails.
NEW QUESTION # 60
You have designed your fabric in Juniper Apstra prior to deploying the network devices. Which Apstra element in the Staged tab would be used to assist the team that is installing and cabling the devices?
Answer: C
Explanation:
The Links table in the Staged tab shows the physical connections between the devices in the fabric. It provides information such as the source and destination device names, hostnames, serial numbers, roles, interfaces, and link status. The Links table can be used to assist the team that is installing and cabling the devices by verifying that the devices are connected correctly and that the links are operational. The Links table can also be used to troubleshoot any connectivity issues that may arise during the installation process.
NEW QUESTION # 61
Referring to the exhibit, how many broadcast domains will an Ethernet frame pass through when traversing the IP fabric from Server A to Server B?
Answer: B
Explanation:
Referring to the exhibit, the image shows a simplified diagram of an IP fabric network connecting two servers, labeled as Server A and Server B. The IP fabric is a network architecture that uses a Clos topology to provide high bandwidth, low latency, and scalability for data center networks.
The IP fabric consists of spine and leaf devices that use BGP as the routing protocol and VXLAN as the overlay technology.
A broadcast domain is a logical portion of a network where any device can directly transmit broadcast frames to other devices at the data link layer (OSI Layer 2). A broadcast frame is a frame that has a destination MAC address of all ones (FF:FF:FF:FF:FF:FF), which means that it is intended for all devices in the same broadcast domain. A broadcast domain is usually bounded by a router, which does not forward broadcast frames to other networks.
In the exhibit, there are two broadcast domains that an Ethernet frame will pass through when traversing the IP fabric from Server A to Server B. The first broadcast domain is the one that contains Server A and the leaf device that it is connected to. The second broadcast domain is the one that contains Server B and the leaf device that it is connected to. The IP fabric itself is not a broadcast domain, because it uses IP routing and VXLAN encapsulation to transport the Ethernet frames over the Layer 3 network.
NEW QUESTION # 62
When viewing the devices in the Managed Devices table, you see that some devices are listed in the OOS-READY state.
What does this state mean for the device?
Answer: C
Explanation:
In Juniper Apstra, a device in the OOS-READY (Out-Of-Service READY) state indicates that the Apstra agent has been installed and the device is prepared to be assigned into a blueprint, but it has not yet been brought into active service within the fabric.
NEW QUESTION # 63
......
Our PracticeDump team know that it is very hard to build trust relationship between the seller and customer. So we are sincerely show our profession and efficiency in JN0-481 exam software to you; we will help you pass JN0-481 exam with our comprehensive questions and detailed analysis of our dumps; we will win your trust with our better customer service. What's more, it is the best recognition for us that you obtain the JN0-481 Exam Certification.
Prep JN0-481 Guide: https://www.practicedump.com/JN0-481_actualtests.html
DOWNLOAD the newest PracticeDump JN0-481 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1ZtpCHiR3VViO8g7JUoGPTS9y4HEfYmbg