In the matter of quality, our VNX301 practice engine is unsustainable with reasonable prices. Despite costs are constantly on the rise these years from all lines of industry, our VNX301 learning materials remain low level. That is because our company beholds customer-oriented tenets that guide our everyday work. The achievements of wealth or prestige is no important than your exciting feedback about efficiency and profession of our VNX301 Practice Engine. So our VNX301 practice materials are great materials you should be proud of and we are!
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
>> VNX301 Reliable Exam Vce <<
We will be happy to assist you with any questions regarding our products. Our VNX301 practice exam DumpTorrent helps to prepare applicants to practice time management, problem-solving, and all other tasks on the standardized VNX301 Exam and lets them check their scores. The VNX301 results help students to evaluate their performance and determine their readiness without difficulty.
NEW QUESTION # 26
A branch has correct underlay speed and no asymmetric SD-WAN paths, but users still report packet loss during large transfers. You suspect QoS shaping is dropping traffic. Which command is most appropriate to verify interface-level CoS drops?
Answer: D
Explanation:
The correct answer is A . Versa throughput troubleshooting documentation includes a specific section titled Check that Packets Are not Dropped by CoS . It states that if a CoS shaper or rate limiter is configured on the VOS device, it may drop packets when traffic exceeds the configured shaping rate. To check whether CoS is dropping packets, Versa recommends commands including show class-of-services interfaces brief and show class-of-services interfaces detail interface-name.
The detailed interface output displays traffic statistics such as TX packets, TX packets dropped, TX bytes, TX bytes dropped, and per-traffic-class drops. This is exactly the evidence needed to confirm whether shaping or QoS enforcement is causing the observed loss.
show alarms last-n 10 may reveal major events but will not provide per-interface CoS drop counters.
show system uptime only indicates how long the system has been running. show cgnat tenants is relevant for NAT state and tenant CGNAT resources, not QoS drops.
NEW QUESTION # 27
A branch user reports poor throughput over an SD-WAN tunnel. The command show interfaces detail vni-0/0 shows the interface is operating at half-duplex / 100 Mbps , although the circuit is expected to run at 1 Gbps full duplex. What is the most likely cause?
Answer: C
Explanation:
The correct answer is C . Versa's bandwidth and throughput troubleshooting documentation specifically instructs administrators to check link speed and half-duplex conditions with the command show interfaces detail interface-name. The example output shows an interface operating at half-duplex / 100 Mbps , and the documentation states that the interface should not be in half-duplex mode and that 100 Mbps was incorrect in that scenario.
A duplex mismatch or incorrect negotiated speed can severely reduce effective throughput, cause collisions or retransmissions, and make SD-WAN overlay performance appear poor even when the overlay itself is functioning. Versa recommends fixing half-duplex and link-speed issues by correcting the configuration on the device to which the VOS device is connected and checking the ISP-side transmission mode, such as auto
/auto.
SLA probing, Controller route advertisement, and VXLAN encapsulation may affect SD-WAN path selection or tunnel formation, but the evidence in the question directly points to a physical or underlay Ethernet negotiation problem.
NEW QUESTION # 28
Examine the exhibit below.
You are configuring an IPsec tunnel towards a non-SD-WAN site over the INETTransport-VR. The site IP address is 10.1.1.1. This tunnel is for traffic between the 192.168.100.0/24 and the 192.168.200.0/24 LAN networks. The tunnel does not establish.
Referring to the exhibit, which statement is correct?
Answer: A
Explanation:
The correct answer is A . The exhibit shows that the IPsec VPN is being configured with Tunnel Routing Instance: XIAN-Control-VR . However, the question states that the tunnel is toward a non-SD-WAN site over the INET-Transport-VR . For a site-to-site IPsec tunnel, the tunnel routing instance must match the routing instance used to reach the peer public IP address. In this case, the remote non-SD-WAN peer is
10.1.1.1 , and the intended underlay transport is INET-Transport-VR , not the Control VR.
Versa troubleshooting documentation explains that routing instances are used to define where traffic is sourced and forwarded. For example, configuration examples select routing instances when enabling services or initiating tests, and traffic must use the correct WAN or transport routing instance to reach the remote endpoint. Versa branch troubleshooting also emphasizes that after transport connectivity is available, the branch establishes IKE-based IPsec connectivity; if that connectivity fails, the IPsec-related interface remains down.
Changing the routing instance to global would not be correct because the intended path is specifically INET-Transport-VR. A higher precedence value is not required to establish the tunnel. The policy selector shown already defines local-to-remote interesting traffic, and the key failure is the incorrect tunnel routing instance.
NEW QUESTION # 29
A branch device is powered on with factory-default staging configuration. The device establishes an IKE session to the staging server and receives an IP address, but it does not proceed to establish an IKE session with the Versa Controller. Which staging phase is failing?
Answer: B
Explanation:
The correct answer is B . In Versa SD-WAN onboarding, the branch progresses through three staging phases.
In Stage 1 , the branch uses its factory-default configuration to start an IKE session with the staging server.
After the IKE session comes up, the staging server assigns an IP address to the branch and notifies the branch of the Versa Director IP address. Versa Director is also notified that the branch has come up.
In Stage 2 , Versa Director pushes the stage-two configuration to the branch through the staging server. This stage changes the IPsec profile so that the Controller IP address becomes the remote IP. The branch reboots and then attempts to establish the IKE session with the Controller. If the device successfully completed Stage
1 but never forms the Controller IKE session, the failure point is Stage 2.
Stage 3 is later, when the device receives stage-three configuration, becomes operational, and creates Controller IPsec plus branch-to-branch VXLAN/ESP sessions. Therefore, the described issue is a Stage
2 staging failure.
NEW QUESTION # 30
Examine the exhibit below.
Spoke1 and Spoke2 are part of Spoke-to-Hub-Only spoke group, the hub is advertising a default route to both the spokes.
Referring to the exhibit, which statement is true?
Answer: A
Explanation:
In Versa SD-WAN, a Spoke-to-Hub-Only topology is specifically designed for deployments where spoke branches communicate only with hub resources and not with other spokes. Versa's SD-WAN design documentation states that in a spoke-to-hub-only topology, the default behavior is that only hub routes are advertised, and spoke routes are not re-advertised by the hub branch. It also explains that this topology is used when spokes do not have to communicate with each other.
Even though the hub in the exhibit advertises a default route, that does not change the topology behavior into spoke-to-spoke communication. The default route can attract unknown traffic from the spokes toward the hub, but the Spoke-to-Hub-Only policy prevents the spoke prefixes from being redistributed or imported in a way that allows spoke-to-spoke reachability. Versa documentation further shows that spoke routes are filtered using BGP communities and import policies, and that the spoke route table contains only destinations behind the hubs, not other spoke routes.
NEW QUESTION # 31
......
Nowadays, online learning is very popular among students. Most candidates have chosen our VNX301 learning engine to help them pass the exam. Our company has accumulated many experiences after ten yearsโ development. We never stop researching and developing the new version of the VNX301 practice materials. With our VNX301 study questions, you can easily get your expected certification as well as a brighter future.
VNX301 Cert: https://www.dumptorrent.com/VNX301-braindumps-torrent.html