The Huawei H19-404_V1.0 Certification is one of the most valuable certificates in the modern Huawei world. This HCSE-Presales-Campus Network Planning and Design V1.0 (H19-404_V1.0) certification exam is designed to validate a candidate's skills and knowledge level. With this H19-404_V1.0 exam everyone whether he is a beginner or seasoned professional can not only validate their expertise but also get solid proof of their skills and knowledge. By doing this you can gain several personal and professional benefits.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: Campus Network Technology Design | 25% | - QoS, security and high availability design - VLAN, IP addressing and routing design - WLAN planning, coverage and roaming design |
| Topic 2: Huawei Campus Network Solutions and Products | 20% | - iMaster NCE-Campus management platform - Switches, WLAN products and AR routers - Xinghe Intelligent Campus Solution overview |
| Topic 3: Scenario-based Campus Network Design | 25% | - Large campus and multi-branch interconnection design - Cloud-managed and virtualized campus network design - Small and medium-sized campus network design |
| Topic 4: Solution Promotion and Project Implementation | 15% | - Solution value analysis and competitive differentiation - Deployment guidance and acceptance criteria |
| Topic 5: Campus Network Planning and Design Fundamentals | 15% | - Network design principles and methodologies - Service requirements and demand analysis - Campus network architecture and evolution |
>> H19-404_V1.0 Preparation <<
They work together and strive hard to maintain the top standard of Huawei H19-404_V1.0 exam practice questions all the time. So you rest assured that with the H19-404_V1.0 Exam Dumps you will ace your Huawei H19-404_V1.0 exam preparation and feel confident to solve all questions in the final Huawei H19-404_V1.0 exam.
NEW QUESTION # 45
On a large campus network, inter-WAC roaming should be avoided as much as possible to ensure the roaming experience.
Answer: A
Explanation:
The statement is true as a WLAN design recommendation. Inter-WAC roaming is supported, but it introduces more control-plane interaction and forwarding complexity than intra-WAC roaming. The Home WAC and Foreign WAC must belong to the same mobility group, synchronize station and AP information, and establish an inter-WAC CAPWAP tunnel for control information and, in some scenarios, service forwarding.
Additional synchronization, tunnel processing, route handling, and failure dependencies can increase roaming delay and complicate troubleshooting. This is especially relevant for delay-sensitive applications such as voice, video, automated guided vehicles, and real-time production systems. A better design places APs between which users frequently move under the same WAC wherever controller capacity and physical topology permit.
Avoiding inter-WAC roaming does not mean disabling the function entirely. Large campuses may require multiple WACs for scale, redundancy, or geographic distribution. Mobility groups should still be configured for unavoidable cross-controller movement. However, buildings, floors, and continuous roaming areas should be assigned carefully so that normal roaming remains intra-WAC. Therefore, the recommendation in the statement is correct, and the answer is True.
NEW QUESTION # 46
Which of the following statements are true about traffic encryption on SD-WAN links?
Answer: A,B
Explanation:
Huawei SD-WAN allows encryption to be controlled by virtual network and by specific device relationships.
When encryption is enabled for a VN, the overlay data channels carrying that VN's traffic use IPsec protection across the relevant WAN links. This provides consistent isolation and confidentiality for the department or service represented by that VN.
Encryption can also be enabled between selected devices or sites. In that case, secure data channels are established for traffic exchanged between those specified endpoints, while other device relationships can continue using GRE without IPsec according to their policies.
Application-specific encryption, as described in option C, is not the supported control granularity. Application identification can influence intelligent traffic steering, QoS, and security-policy selection, but it does not mean that only the payload of a selected application is independently encrypted inside an otherwise unencrypted SD-WAN tunnel.
A transport network is an underlay WAN such as MPLS or the Internet. Enabling encryption is an overlay tunnel policy rather than a mechanism that encrypts all traffic belonging to an entire TN. Huawei distinguishes TNs as underlay networks and GRE or IPsec VPNs as overlay data channels. Therefore, only A and B are correct.
NEW QUESTION # 47
Which of the following capabilities were introduced with Wi-Fi 7?
Answer: C,D
Explanation:
The capabilities introduced with Wi-Fi 7 are 4096-QAM and channel bandwidth of up to 320 MHz. Wi-Fi 7, based on IEEE 802.11be Extremely High Throughput, doubles the maximum channel width available under Wi-Fi 6 and Wi-Fi 6E from 160 MHz to 320 MHz where sufficient regulatory spectrum is available. It also introduces 4096-QAM, encoding 12 bits per modulation symbol compared with 10 bits for Wi-Fi 6's 1024- QAM. This can increase peak spectral efficiency when the signal-to-noise ratio is sufficiently high.
The other options were available before Wi-Fi 7. Support for up to eight spatial streams existed in earlier IEEE 802.11 generations, and MU-MIMO was already supported before Wi-Fi 7, with major uplink and downlink enhancements delivered by Wi-Fi 6. The 6 GHz band was commercially introduced through Wi-Fi
6E. Huawei's material specifically describes Wi-Fi 6E as extending Wi-Fi 6 into the 6 GHz spectrum. Wi-Fi 7 continues using 6 GHz but did not introduce it. Therefore, only A and C are correct.
NEW QUESTION # 48
How many ports can a 400GE card offer on the CloudEngine S16700 series next-generation flagship core switches?
Answer: A
Explanation:
A high-density 400GE service card for the CloudEngine S16700 series can provide 18 ports. The S16700 is positioned as a next-generation flagship campus core switch designed for ultra-high-capacity aggregation, large-scale Wi-Fi backhaul, data-center interconnection, and long-term bandwidth evolution.
An 18-port 400GE card provides a theoretical aggregate port rate of 7.2 Tbit/s in each direction before considering the switching fabric's internal architecture and forwarding design. This density allows a single chassis slot to aggregate numerous high-speed distribution switches, connect multiple campus fabrics, or provide high-bandwidth links toward data centers and service platforms. It also reduces the number of cards and chassis required compared with lower-density 8-port, 12-port, or 16-port alternatives.
The question asks specifically for the number of physical 400GE interfaces offered by the card, not the entire chassis capacity or the number of ports after breakout. Under the H19-404 product-portfolio specification represented by this question, the correct density is 18 native 400GE ports. Therefore, option B is correct.
NEW QUESTION # 49
Which of the following statements is true about an AP's transmit power?
Answer: A
Explanation:
An AP's transmit power must be maintained within an appropriate range. Excessive power does not automatically improve service quality. A high-power AP can enlarge its interference domain, create co- channel or adjacent-channel interference, produce asymmetric uplink and downlink coverage, and cause sticky-client behavior because a station continues hearing an AP even when its weaker transmission cannot reliably reach that AP. Huawei states that high-power APs can interfere with adjacent APs and that radio calibration dynamically adjusts AP channels, power, and frequency bands to ensure coverage while minimizing interference.
Conversely, power that is too low creates coverage holes, weak received signal strength, low modulation rates, retransmissions, and roaming instability. When a new AP is added, neighboring APs may reduce their transmit power to limit interference. When an AP goes offline, neighboring APs may increase power to compensate for the missing coverage. The engineering objective is therefore neither maximum nor minimum power, but sufficient coverage with controlled overlap and minimum interference. Accordingly, option B is correct.
NEW QUESTION # 50
......
If you are going to purchase H19-404_V1.0 test materials online, the safety of the website is significant. We provide you with a clean and safe online shopping environment if you buying H19-404_V1.0 trining materials form us. We have professional technicians to exam the website every day, therefore the safety for the website can be guaranteed. Moreover, H19-404_V1.0 Exam Materials are high quality and accuracy, and you can pass the exam just one time. We offer you free update for 356 days for H19-404_V1.0 traing materials and the update version will be sent to your email automatically.
Valid H19-404_V1.0 Exam Voucher: https://www.trainingquiz.com/H19-404_V1.0-practice-quiz.html