You can pass your Fortinet NSEI_OTS_AR-7.6 certification exam in less time, without wasting time and money on outdated or unreliable Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam study materials. Don't let fear or a lack of resources hold you back from achieving your goals, trust TopExamCollection Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) practice test material and achieve the highest marks in your Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam.
| Section | Weight | Objectives |
|---|---|---|
| Network Security | 25% | - Deep inspection for industrial protocols (Modbus, DNP3, OPC) - Virtual patching for legacy OT systems - Security automation and threat response |
| Asset Management | 25% | - OT security standards and compliance (IEC 62443, NIST) - Fortinet Security Fabric for OT environments - Device detection and inventory using FortiGate & FortiNAC |
| Monitoring and Risk Assessment | 25% | - OT-focused risk assessment and management - Threat detection using FortiSIEM 7.4 - Event handling and logging with FortiAnalyzer 7.6 |
| Network Access Control | 25% | - OT Ethernet and industrial communication models - Purdue Model and secure network segmentation - Authentication and access policies for OT devices |
>> NSEI_OTS_AR-7.6 Practice Online <<
Our NSEI_OTS_AR-7.6 simulating exam is made by our responsible company which means you can gain many other benefits as well. On condition that you fail the exam after using our NSEI_OTS_AR-7.6 study prep unfortunately, we will switch other versions for you or give back full of your refund. If you are interested to our NSEI_OTS_AR-7.6 simulating exam, just place your order now. And you will receive it only in a few minutes.
NEW QUESTION # 18
Refer to the exhibit.
Based on the information provided on the partial Event Monitor page shown in the exhibit, how was the attack detected? (Choose one answer)
Answer: C
Explanation:
The correct answer is D. Automatically by an event handler . The study guide explicitly states that "Event handlers generate events on FortiAnalyzer" and "FortiAnalyzer uses event handlers to filter all incoming logs. If the logs received match the conditions set in the event handlers, FortiAnalyzer generates an event." It also says "You can view all generated events on the Event Monitor page." This directly matches the exhibit, which is showing entries on the Event Monitor page. Therefore, the attack shown there was detected automatically through an event handler .
The guide also explains the detection flow: "FortiAnalyzer receives logs," "FortiAnalyzer parses logs," and "FortiAnalyzer generates an event if a rule is matched in an event handler." In addition, the Event Monitor view includes the Handler column, which identifies the event handler that generated the event. That is why the attack is not considered manually detected, and it is not primarily detected by a playbook or stitch.
Playbooks and stitches are used for subsequent automation actions, but the event appearing in Event Monitor is created by the event handler mechanism.
NEW QUESTION # 19
During layer 2 polling , which two pieces of information are gathered by FortiNAC to identify a device?
(Choose two answers)
Answer: B,D
NEW QUESTION # 20
Refer to the exhibits.
A partial Incident Analysis page and the log details related to the event are shown. An attack is reported on your OT network. You analyze the corresponding incident. Based on the information provided on the Incident Analysis page and the log details, which two statements are correct? (Choose two answers)
Answer: D,E
Explanation:
Based on the technical data provided in the exhibits and the OT Security 7.6 Architect curriculum:
* Industrial Protocol Identification (Statement A) : The log details exhibit clearly shows that the Destination Port used in the attack is 502 . According to the study guide ' s section on Industrial Protocol Protection , the standard port used by the Modbus TCP protocol is 502 . Furthermore, the attack name identifies a " Triangle.Research.Nano-10.PLC, " which are industrial controllers commonly utilizing Modbus for communications.
* Attack Mitigation (Statement B) : The log details specify that the Action taken by the FortiGate (Edge-FortiGate) was dropped . In cybersecurity and Fortinet fabric operations, dropping a packet associated with an IPS signature means the traffic was blocked from reaching its target, thereby mitigating the attack.
* Target IP Address (Statement E) : The log detail explicitly lists the Destination IP as 192.168.2.3 .
The Incident Analysis page also titles the incident with dstip:192.168.2.3. While the " Affected Endpoint " is shown as 10.1.5.20 , in an " outgoing " attack direction (as shown in the log), this likely refers to the internal source/attacker IP, whereas the target is the destination IP (192.168.2.3). Thus, Statement E is incorrect.
* Protocol Conflict (Statement C) : The IEC 104 protocol typically utilizes port 2404 . Since the log specifies port 502, Statement C is incorrect.
* Severity Distinction (Statement D) : While the Incident severity is marked as High , the question specifically asks about event severity. The " Events " table at the bottom of the Incident Analysis page shows a " User login/logout failed " event with a medium severity. Because there is a distinction in the management console between the severity of individual events and the aggregated incident, and Statement A and B are technically definitive based on port and action, A and B are the correct architectural choices.
NEW QUESTION # 21
What are two advantages provided by industrial Ethernet? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are B. Real-time control and D. Determinism . The study guide defines industrial Ethernet as the "use of Ethernet and TCP/IP as transport mechanisms for industrial protocols" and states that it provides "real-time control," "low latency," and "determinism (meaning reliable and predictable data delivery)" in harsh environments. It further explains that industrial Ethernet "provides deterministic communication between machine controllers, actuators, sensors, and other units." These statements directly confirm that the two key advantages are real-time control and determinism.
The other options are not supported by the study guide as core advantages of industrial Ethernet. Encryption is not listed as one of the benefits in this section, and remote access is discussed elsewhere in the OT architecture but not as a defining advantage of industrial Ethernet itself. The guide is explicit that the main benefits here are predictable delivery and real-time communication, which are essential in industrial control environments where timing and reliability matter.
NEW QUESTION # 22
Refer to the exhibit. A partial OT network is shown. You must improve the security of this OT network and implement internal segmentation between network 1 and network 2. How can you achieve the segmentation?
(Choose one answer)
Answer: A
Explanation:
The correct answer is D. You can configure forward domain IDs for each network . The study guide explains that in FortiGate transparent mode, "all interfaces belong to the same broadcast domain, even interfaces with different VLAN IDs" and then states that you should "use this command to subdivide into multiple broadcast domains" with set forward-domain < domain_ID > . It further explains that
"interfaces with the same domain ID belong to the same broadcast domain" and "traffic arriving on one interface is broadcast only to interfaces in the same forward domain ID." This is exactly the mechanism used to separate one internal network from another and improve segmentation.
The other options do not match this requirement. Universal ZTNA is described as controlling user access to applications , not segmenting two internal OT networks. An explicit software switch is for controlling intra- switch or intra-VLAN traffic inside the same software switch broadcast domain, which is more aligned with microsegmentation than separating two routed internal networks. One traffic VDOM does not create segmentation by itself; segmentation with VDOMs requires multiple VDOMs, not one. Therefore, the best choice for segmenting network 1 and network 2 in this scenario is to assign separate forward domain IDs .
NEW QUESTION # 23
......
Our NSEI_OTS_AR-7.6 exam braindumps are famous for the advantage of high-efficiency and high-effective. And it is proved by the high pass rate. The 99% pass rate is a very proud result for us. If you join, you will become one of the 99% to pass the NSEI_OTS_AR-7.6 Exam and achieve the certification. Believe in yourself, you can do it! Buy NSEI_OTS_AR-7.6 study guide now and we will help you. Believe it won't be long before, you are the one who succeeded!
NSEI_OTS_AR-7.6 Cost Effective Dumps: https://www.topexamcollection.com/NSEI_OTS_AR-7.6-vce-collection.html