The Actual4dump is a leading platform that is committed to ace the Fortinet NSEI_OTS_AR-7.6 exam preparation and enabling the candidates to pass the final Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam easily. To achieve this objective the Actual4dump is offering real and updated Fortinet Certifications NSEI_OTS_AR-7.6 Exam Questions. These Fortinet NSEI_OTS_AR-7.6 exam questions are designed and verified by qualified NSEI_OTS_AR-7.6 subject matter experts.
| Section | Objectives |
|---|---|
| Topic 1: Asset Management | - Implement device detection on FortiGate and FortiNAC - Explain OT standards and Fortinet compliance - Use Fortinet Security Fabric for an OT network |
| Topic 2: Network Security | - Configure virtual patching - Configure automation - Configure security inspections for industrial protocols |
| Topic 3: Network Access Control | - Configure network segmentation schemas - Configure network access authentication - Explain OT Ethernet concepts |
| Topic 4: Monitoring and Risk Assessment | - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers - Perform risk assessment and management |
>> New NSEI_OTS_AR-7.6 Braindumps <<
You should practice with Actual4dump Fortinet NSEI_OTS_AR-7.6 exam questions that are aligned with the latest content of the Fortinet NSEI_OTS_AR-7.6 test. Actual4dump Fortinet NSEI_OTS_AR-7.6 questions are designed to provide you with the knowledge essential to get certified very quickly. These Fortinet exam questions remove the need for you to spend time on unnecessary or irrelevant material, allowing you to complete your NSEI_OTS_AR-7.6 Exam Preparation swiftly.
NEW QUESTION # 34
Refer to the exhibit.
A partial OT network is shown. In this OT network, you must add additional security measures to detect OT protocols and, therefore, increase the traffic visibility. Which security sensor must you implement to detect the OT protocols in this network? (Choose one answer)
Answer: B
Explanation:
The correct answer is C. Application sensor set to monitor on all the FortiGate devices .
The study guide clearly explains that application control is the feature used to identify OT protocols. It states that "application control detects the protocols used in applications like Modbus, IEC 104, and the contents of the telecontrol messages" and also says "You can use application control signatures to detect OT protocols." It further shows an example where a Modbus application control profile is enabled on a firewall policy "for OT protocol visibility in the monitor status." This directly matches the requirement in the question, which is to detect OT protocols and increase traffic visibility .
The other options do not fit the requirement as precisely. Device detection is for identifying devices and collecting endpoint information, not for detecting industrial protocols. Inline IDS and IPS are focused more on detecting or blocking attacks, exploits, protocol abnormalities, and known vulnerabilities. While IPS can inspect some OT traffic, the study guide distinguishes it from application control by stating that IPS signatures tend to detect exploits, whereas application control signatures tend to provide protocol detection at various levels . Therefore, the required security sensor for OT protocol detection and traffic visibility is the application sensor in monitor mode .
NEW QUESTION # 35
You want FortiAnalyzer to trigger an automation stitch on a FortiGate device automatically. What must you configure on FortiAnalyzer to enable direct communication with FortiGate? (Choose one answer)
Answer: A
Explanation:
The verified answer is C. The Fabric settings . The study guide ties FortiAnalyzer-triggered actions to the Security Fabric relationship with FortiGate, not to playbook tasks or standalone event handlers alone. It explains that "within the Security Fabric environment, FortiAnalyzer is a key element in the creation of automation stitches" and shows the flow where a downstream FortiGate sends logs to FortiAnalyzer, then FortiAnalyzer parses the logs and notifies the root FortiGate , after which the root FortiGate triggers the action . This shows that FortiAnalyzer must be configured so it can communicate with FortiGate through the Security Fabric.
The guide also states that FortiAnalyzer is the foundation of the Security Fabric , providing logging, reporting, analytics, and automation for Fabric devices and endpoints. It further explains that the FortiAnalyzer Fabric connector consolidates the traffic logs within the Security Fabric. This confirms that the automation workflow depends on proper Security Fabric integration. A playbook task is used for automated SOC actions, and an event handler is used to generate events from logs, but neither one alone establishes the direct communication path needed between FortiAnalyzer and FortiGate. Therefore, the required configuration on FortiAnalyzer is the Fabric settings .
NEW QUESTION # 36
Refer to the exhibit.
A Virtual Patching profile is shown. You have recently updated your SCADA system and would like to apply the SCADA virtual patching profile. Which two statements about this profile are correct? (Choose two answers)
Answer: A,C
Explanation:
The correct answers are B and D .
Option B is correct because the profile has Medium , High , and Critical selected, while Low severity is not selected. That means low-severity virtual patching signatures are not enforced by this profile. So for the device with MAC address 12:12:12:12:12 , low-severity signatures are not blocked. The study guide explains virtual patching as device-specific protection where "FortiGate caches the signatures and mitigation rules that apply to each device" and applies them when the related traffic matches the firewall policy.
Option D is correct because the Virtual Patching Exemptions table shows a row with the MAC address 11:
11:11:11:11 and no specific signature listed. The study guide states that in the Virtual Patching profile you can "Exempt a specific device with the MAC address or a specific signature." A MAC-only exemption means that specific device is excluded from virtual patching enforcement, so in practical terms it is treated as having no applicable vulnerabilities in this profile.
Option C is incorrect because the profile does not block critical signatures for all devices. The exemptions list proves that at least one device can be excluded by MAC address, and a specific signature can also be exempted. Therefore, enforcement is not universal across all devices.
Option A is incorrect because the entry Schneider.Electric.ClearSCADA.HTTP.Interface.XSS appears as a specific signature exemption , not as the only remaining vulnerability. The profile display is showing exemptions, not a statement that only one vulnerability is still present.
NEW QUESTION # 37
In your OT environment, you want to detect the devices passively. Which two methods must you implement?
(Choose two answers)
Answer: A,C
Explanation:
The correct answers are C. Vendor OUI and D. Network traffic .
The study guide explicitly separates active/direct profiling methods from passive/non-direct methods and states that "In OT environments, passive methods are preferred over active methods." It then lists the methods that do not require FortiNAC to interact directly with the device being profiled. Among those methods are "Network traffic: gathered from the infrastructure" and "Vendor OUI: determined by the MAC address gathered from the infrastructure." That directly matches options C and D .
Options A and B are incorrect because SSH and SNMP are shown in the guide under the direct/active profiling methods. The guide's point is that passive detection avoids directly scanning or interacting with OT endpoints, since that can negatively affect performance in industrial environments. Because the question specifically asks for passive detection methods, the correct pair is Vendor OUI and Network traffic .
NEW QUESTION # 38
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: D
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 39
......
The most interesting thing about the learning platform is not the number of questions, not the price, but the accurate analysis of each year's exam questions. Our NSEI_OTS_AR-7.6 guide dump through the analysis of each subject research, found that there are a lot of hidden rules worth exploring, this is very necessary, at the same time, our NSEI_OTS_AR-7.6 training materials have a super dream team of experts, so you can strictly control the proposition trend every year. In the annual examination questions, our NSEI_OTS_AR-7.6 study questions have the corresponding rules to summarize, and can accurately predict this year's test hot spot and the proposition direction. This allows the user to prepare for the test full of confidence.
Practice NSEI_OTS_AR-7.6 Exam Fee: https://www.actual4dump.com/Fortinet/NSEI_OTS_AR-7.6-actualtests-dumps.html