International Code Council M2 시험을 어떻게 통과할수 있을가 고민중이신 분들은DumpTOP를 선택해 주세요. DumpTOP는 많은 분들이 IT인증시험을 응시하여 성공하도록 도와주는 사이트입니다. 최고급 품질의International Code Council M2시험대비 덤프는International Code Council M2시험을 간단하게 패스하도록 힘이 되어드립니다. DumpTOP 의 덤프는 모두 엘리트한 전문가들이 만들어낸 만큼 시험문제의 적중률은 아주 높습니다.
| Section | Weight | Objectives |
|---|---|---|
| Duct Systems | 12% | - Dampers and access doors - Duct construction and materials - Duct installation and supports - Insulation and sealing |
| Heating, Cooling & Water Heaters | 18% | - Boilers and hydronic systems - HVAC equipment installation and clearance - Solar thermal systems - Heat pumps and cooling equipment - Water heaters and storage tanks |
| Exhaust & Ventilation Systems | 20% | - Hazardous and special exhaust systems - Ventilation rates and outdoor air requirements - Makeup air systems - Commercial kitchen exhaust systems |
| Fuel Supply Systems | 10% | - Pressure regulation and overpressure protection - Gas appliances and connections - Fuel gas piping materials and installation - Piping testing and inspection |
| Chimneys & Vents | 14% | - Vent systems and connections - Factory-built chimneys and vents - Clearances and termination requirements - Chimney construction and materials |
| Combustion Air | 8% | - Confined spaces and equipment rooms - Air supply and venting - Combustion air requirements |
| General Administration | 18% | - Permits and inspections - Plan review and documentation - Manufacturer's instructions and listings - Code authority and enforcement |
>> International Code Council M2퍼펙트 공부 <<
DumpTOP 제공 International Code Council M2시험덤프자료가 광범한 시험준비인사들의 찬양을 받은지 하루이틀일이 아닙니다.이렇게 많은 분들이DumpTOP 제공 International Code Council M2덤프로 시험을 통과하여 자격증을 취득하였다는것은DumpTOP 제공 International Code Council M2덤프가 믿을만한 존재라는것을 증명해드립니다. 덤프에 있는 문제만 열심히 공부하시면 시험통과 가능하기에 시간도 절약해줄수있어 최고의 믿음과 인기를 받아왔습니다. International Code Council M2 시험을 봐야 하는 분이라면DumpTOP를 한번 믿어보세요. DumpTOP도움으로 후회없이 멋진 IT전문가로 거듭날수 있을것입니다.
질문 # 32
Unless listed for a greater or smaller dimension, mechanical draft venting systems shall terminate a minimum of _____ feet below an openable window.
정답：A
설명：
For mechanical draft venting systems, unless the appliance is listed for a different clearance, the vent terminal must be located not less than 4 feet below , 4 feet horizontally from , or 1 foot above any door, operable window, or gravity air inlet into a building. Therefore, the required minimum distance below an openable window is 4 feet , so Option B is correct.
질문 # 33
Given: A recirculating industrial direct-fired makeup air heater has a rated input of 200,000 Btu/h .
Ventilation air is supplied by separate mechanical means.
Outside ventilation air shall be provided to supply at least _____ CFM.
정답：C
설명：
The applicable provision requires direct-fired industrial air heaters to supply outside ventilation air at a rate of not less than 4 cfm per 1,000 Btu/h of rated input where ventilation air is provided by separate mechanical means. For 200,000 Btu/h , the required outside air is:
200,000 ÷ 1,000 = 200
200 × 4 = 800 cfm
So the correct answer is C
질문 # 34
To test for tightness, a consumer's gas piping should never be filled with:
정답：C
설명：
The IFGC section on test medium states that the test medium shall be air, nitrogen, carbon dioxide or an inert gas , and specifically states that oxygen shall not be used as a test medium . That makes C the correct answer.
질문 # 35
Ducts shall not be permitted to be connected to:
정답：B
설명：
The IMC appliance provisions prohibit duct connection to a vented wall furnace . That makes Option B correct. The exam tests recognition of appliance-specific distribution restrictions rather than general duct rules.
질문 # 36
A cooling system with a condensate disposal system:
정답：A
설명：
The ICC mechanical code requires condensate disposal components to be of approved corrosion-resistant material , and the drain line shall not decrease in size from the drain pan connection to the place of disposal.
The code minimum size is 3/4 inch , so the 1/2-inch statement is incorrect, and the code is not limited to PVC only. Also, the slope requirement for horizontal drain piping is not less than 1/8 inch per foot , not 1/4 inch per foot. That makes Option A the only fully correct statement.
질문 # 37
......
IT인증자격증은 여느때보다 강렬한 경쟁율을 보이고 있습니다. International Code Council 인증M2시험을 통과하시면 취직 혹은 승진이나 연봉협상에 많은 도움이 되어드릴수 있습니다. International Code Council 인증M2시험이 어려워서 통과할 자신이 없다구요? DumpTOP덤프만 있으면 이런 고민은 이제 그만 하지않으셔도 됩니다. DumpTOP에서 출시한 International Code Council 인증M2덤프는 시장에서 가장 최신버전입니다.
M2최신 시험 예상문제모음: https://www.dumptop.com/International-Code-Council/M2-dump.html