DumpTOP의 Cisco인증 350-101덤프를 구매하시고 공부하시면 밝은 미래를 예약한것과 같습니다. DumpTOP의 Cisco인증 350-101덤프는 고객님이 시험에서 통과하여 중요한 IT인증자격증을 취득하게끔 도와드립니다. IT인증자격증은 국제적으로 인정받기에 취직이나 승진 혹은 이직에 힘을 가해드립니다. 학원공부나 다른 시험자료가 필요없이DumpTOP의 Cisco인증 350-101덤프만 공부하시면Cisco인증 350-101시험을 패스하여 자격증을 취득할수 있습니다.
| 주제 | 소개 |
|---|---|
| 주제 1 |
|
| 주제 2 |
|
| 주제 3 |
|
| 주제 4 |
|
| 주제 5 |
|
| 주제 6 |
|
>> Cisco 350-101최신 업데이트버전 인증덤프 <<
Cisco 350-101 시험자료를 찾고 계시나요? DumpTOP의Cisco 350-101덤프가 고객님께서 가장 찾고싶은 자료인것을 믿어의심치 않습니다. Cisco 350-101덤프에 있는 문제와 답만 기억하시면 시험을 쉽게 패스하여 자격증을 취득할수 있습니다. 시험불합격시 덤프비용 환불가능하기에 시험준비 고민없이 덤프를 빌려쓰는것이라고 생각하시면 됩니다.
질문 # 79
Refer to the exhibit. A network engineer is designing a Wi-Fi deployment for a high-density office environment. The engineer must select the appropriate channel plan to minimize co-channel interference (CCI) in the 2.4 GHz band. Which strategy is recommended to reduce CCI?
정답：D
설명：
In the 2.4 GHz band, IEEE 802.11b/g/n Wi-Fi uses channels that are 20 MHz wide but only partially non-overlapping. Cisco Wireless design guides recommend using only non-overlapping channels to prevent co-channel interference (CCI), which occurs when adjacent APs transmit on overlapping frequencies and contend for airtime, resulting in reduced throughput and increased latency. The standard non-overlapping channels in North America are 1, 6, and 11. By carefully assigning these channels to adjacent access points, the RF designer ensures that no two neighboring APs share overlapping channels, thereby minimizing CCI and improving overall network performance.
질문 # 80
A network engineer is integrating Cisco ISE with a wireless controller for 802.1X authentication. The controller is registered with Cisco ISE as a network device. To secure communication, the engineer must configure a shared secret for RADIUS authentication. Which CLI command on the WLC accomplishes this task?
정답：D
설명：
The correct command iskey 0 MySecretKey123under RADIUS server configuration mode. On a Catalyst
9800 WLC, the RADIUS server is defined with radius server < radius-server-name > , then the server address and ports are configured, and the shared secret is applied with the key < shared-key > command. Cisco's Catalyst 9800 802.1X configuration workflow shows the exact sequence: radius server < radius-server-name
> , address ipv4 < radius-server-ip > auth-port 1812 acct-port 1813, and key < shared-key > .
Cisco IOS XE command examples also show Device(config-radius-server)# key 0 cisco, with Cisco describing it as setting the clear-text key for the RADIUS authentication server. The 0 indicates that the key is entered in clear-text form at the CLI; it does not mean "no security." The value must match the shared secret configured for the WLC network device in Cisco ISE, otherwise RADIUS Access-Request messages are rejected or ignored. Options A, B, and C are not valid Catalyst 9800 RADIUS server subcommands.
Reference topic:Client Connectivity Configuration - WPA2/WPA3 Enterprise, 802.1X, Cisco ISE integration, RADIUS server objects, AAA method lists, and shared-secret configuration.
질문 # 81
Refer to the exhibit. A JSON response from a wireless management API contains access point inventory and interface state information. Which JSON expression retrieves the MAC address of the second interface on the first access point?
정답：D
설명：
The correct expression is accessPoints[0].interfaces[1].macAddress. The JSON object contains a top-level key named accessPoints, whose value is an array. Array indexing begins at zero, so accessPoints[0] selects the first access point object, ap-west-1. Inside that object, the interfaces key also contains an array. Therefore, interfaces[1] selects the second interface object, which has slot: 1, status: "down", and macAddress: "CC:FA:00:11:22:34". The final selector, .macAddress, returns that MAC address value.
This structure is directly aligned with Cisco automation workflows, where RESTCONF and Catalyst Center APIs exchange structured data in JSON. Cisco documents that Catalyst Center REST API payloads are JSON-formatted, and its example describes JSON as key-value data separated by colons. Cisco also states that Catalyst 9800 RESTCONF uses structured XML or JSON with YANG models for programmatic device access. Option B selects ap-east-2. Option C selects the first interface on ap- west-1. Option D references a non-existent second interface on ap-east-2.
질문 # 82
What does a high SNR value result in?
정답：A
설명：
Signal-to-Noise Ratio (SNR) is a critical metric in wireless networking that quantifies the relationship between the received signal power and the background noise. A higher SNR indicates that the signal strength is significantly stronger than the noise level, which directly impacts the quality and reliability of wireless communication. When SNR is high, the receiver can more accurately decode transmitted frames, leading to fewer errors, reduced retransmissions, and improved data integrity. This results in more consistent throughput and better overall performance of wireless clients, especially in environments with high client density or potential sources of interference. Conversely, a low SNR increases susceptibility to multipath distortion, frame loss, and degraded network performance. Option C correctly identifies the outcome of a high SNR: enhanced data integrity with fewer errors.
질문 # 83
A business requires a Cisco 9163E AP to act as a point-to-point connection between two buildings on campus. No wired connection is available between the sites, and the AP must relay network traffic across the wireless link. The administrator must ensure that the AP is configured to forward Ethernet frames between its radio and Ethernet interfaces. Which CLI command must the administrator use to configure the AP for this application?
정답：A
설명：
In point-to-point wireless deployments, the AP must act as a transparent bridge, forwarding Ethernet frames between the wired network interface and the wireless radio. The correct configuration command in Cisco IOS XE for a Cisco 9163E AP is ap name <ap_name> mode bridge. This sets the AP into bridge mode, allowing it to function as a Layer 2 relay between the two connected sites, effectively extending the Ethernet network over the wireless link.
질문 # 84
......
IT업계 취업 준비생이라면 국제적으로도 승인받는 IT인증자격증 정도는 몇개 취득해야 하지 않을가 싶습니다. Cisco인증 350-101시험을 통과하여 인기 자격증을 취득하시면 취업경쟁율이 제고되어 취업이 쉬워집니다. DumpTOP의Cisco인증 350-101덤프는 많은 시험본 분들에 의해 검증된 최신 최고의 덤프공부자료입니다.망설이지 마시고DumpTOP제품으로 한번 가보세요.
350-101최신 시험대비 공부자료: https://www.dumptop.com/Cisco/350-101-dump.html