여러분은Fortinet FCP_FSA_AD-5.0인증시험을 패스함으로 IT업계관련 직업을 찿고자하는 분들에게는 아주 큰 가산점이 될수 있으며, 성덩한 IT업계사업자와 한걸음 가까와 집니다.
| 주제 | 소개 |
|---|---|
| 주제 1 |
|
| 주제 2 |
|
| 주제 3 |
|
| 주제 4 |
|
PassTIP는Fortinet FCP_FSA_AD-5.0인증시험의 촉매제 같은 사이트입니다.Fortinet FCP_FSA_AD-5.0인증시험 관연 덤프가 우리PassTIP에서 출시되었습니다. 여러분이Fortinet FCP_FSA_AD-5.0인증시험으로 나 자신과 자기만의 뛰어난 지식 면을 증명하고 싶으시다면 우리 PassTIP의Fortinet FCP_FSA_AD-5.0덤프자료가 많은 도움이 될 것입니다.
질문 # 18
You are asked to create an 802.3ad interface on FortiSandbox with port 2 and port 4. However, when attempting to make the configuration change, you discover that you cannot select port 4 for the aggregate bonding. What are two reasons for this issue? (Choose two answers)
정답：C,D
설명：
From the Deployment and System Settings lesson, the Study Guide states:
"Other ports, with the exception of port3, can also be configured as management ports from CLI."
"You can set additional ports as management port using the CLI command shown on this slide." From the Lab Guide (Exercise 4 - Using Inline Scanning):
"FortiGate and FortiSandbox communicate through port 4443. Management or API ports grant access through port 4443."
"Enter the following command to enable API access on port2: set api-port port2" Ports that are designated as either administration interfaces or API interfaces cannot be selected for 802.3ad aggregate bonding because:
Option A - Port 4 configured as an administration interface is reserved for management traffic and cannot be repurposed for link aggregation Option C - Port 4 configured as an API interface is dedicated for API communication (port 4443) and is similarly restricted from being used in aggregate bonding configurations Port 4 in the Lab Guide is specifically referenced as the HA communication and management port, confirming these restrictions apply when special roles are assigned to interfaces.
질문 # 19
Refer to the exhibit.
Which command must you use to configure the FortiSandbox device as the primary node? (Choose one answer)
정답：D
설명：
The exhibit labels 10.25.1.50 as the cluster virtual IP address. The Study Guide explains that in HA configuration, "You must configure the HA group name, password, and the virtual IP only on the primary node." It also says: "You must also configure an external interface for external communication and an IP address that will be used as a virtual IP for the whole cluster. Devices will interact with the cluster using this virtual IP." That is why the command for the primary node must point to the cluster virtual IP, not to the individual port1 addresses of the primary, secondary, or upstream firewall. In the exhibit, 10.25.1.30 is the primary node's own port1 IP, 10.25.1.40 is the secondary node's port1 IP, and 10.25.1.254 is the network device. The only address that matches the required cluster virtual IP is 10.25.1.50, so the correct command is hc-settings -si iport1 -a10.25.1.50.
질문 # 20
To assign a file to a VM image, which two conditions must be true? (Choose two answers)
정답：A,D
설명：
From the Scanning and Rating Components lesson, the Study Guide explicitly states:
"The second section of the Scan Profile, VM Association, allows you to define file extensions and VM image associations. This means that specific files are sandboxed by the associated VM image. To assign a file to a VM image, the following conditions must be true:
The file type must be configured to enter the job queue (first section of the scan profile).
The VM image clone value cannot be a non-zero number."
This directly confirms:
Option B - The VM image clone value must be a non-zero number (clones must be allocated) Option C - The file type must be configured to enter the job queue via the scan profile Pre-Filter section Options A and D, while potentially relevant in practice, are not listed as the two required conditions in the Study Guide.
질문 # 21
Review the exhibits.
A FortiMail device is integrated with a FortiSandbox device. What is the expected behavior on FortiMail for emails that require FortiSandbox inspection? (Choose one answer)
정답：A
설명：
From the FortiMail Integration lesson, the Study Guide explicitly states:
"The Scan timeout value determines how long FortiMail will wait for a response from FortiSandbox. The default is 30 minutes. So, if after 30 minutes FortiSandbox is unable to generate a verdict, FortiMail will release the email to the end user."
"SMTP is a store-and-forward protocol. This allows FortiMail to queue the email while FortiSandbox inspects all submitted samples. FortiMail will release the email only if there is a scan timeout event, or FortiSandbox returns a clean verdict." The Integration Settings exhibit clearly confirms Scan timeout = 30 minutes, and the AV Profile shows both Attachment analysis and URL analysis are enabled - meaning FortiMail will hold/queue emails for up to 30 minutes while FortiSandbox completes inspection of all attachments and URLs before taking action.
질문 # 22
Refer to the exhibits.
You are unable to download guest VMs on a new FortiSandbox VM. What is the reason for this? (Choose one answer)
정답：D
설명：
From the Scanning and Rating Components lesson, the Study Guide explicitly states:
"VM images are downloaded from FortiGuard, using port1. So, you must ensure FortiSandbox has a default route and internet connectivity for port1." The exhibit confirms this - the test-network output shows:
System DNS resolve: Failed for both bing.com and fsavm.fortinet.net
fsavm.fortinet.net is the FortiGuard VM image download server
This DNS failure on the system side (port1) confirms there is no internet connectivity on port1, preventing VM image downloads. Note that port3 internet shows "Warning: VM to access internet: Disabled" - but port3 is only for VM sandboxing traffic, not for downloading VM images.
질문 # 23
......
인재도 많고 경쟁도 치열한 이 사회에서 IT업계 인재들은 인기가 아주 많습니다.하지만 팽팽한 경쟁률도 무시할 수 없습니다.많은 IT인재들도 어려운 인증시험을 패스하여 자기만의 자리를 지켜야만 합니다.우리 PassTIP에서는 마침 전문적으로 이러한 IT인사들에게 편리하게 시험을 패스할수 있도록 유용한 자료들을 제공하고 있습니다. Fortinet 인증FCP_FSA_AD-5.0인증은 아주 중요한 인증시험중의 하나입니다. PassTIP의Fortinet 인증FCP_FSA_AD-5.0로 시험을 한방에 정복하세요.
FCP_FSA_AD-5.0유효한 공부: https://www.passtip.net/FCP_FSA_AD-5.0-pass-exam.html