If you want to pass the exam in the shortest time, our study materials can help you achieve this dream. NSEI_OTS_AR-7.6 learning quiz according to your specific circumstances, for you to develop a suitable schedule and learning materials, so that you can prepare in the shortest possible time to pass the exam needs everything. If you use our NSEI_OTS_AR-7.6 training prep, you only need to spend twenty to thirty hours to practice our NSEI_OTS_AR-7.6 study materials and you are ready to take the exam.
| Section | Objectives |
|---|---|
| Asset management | - Explain OT standard and Fortinet compliance - Implement device detection on FortiGate and FortiNAC - Fortinet Security Fabric for an OT network |
| Network access control | - Explain OT Ethernet concepts - Configure network access authentication - Configure network segmentation schemas |
| Monitoring and risk assessment | - Analyze security reports from FortiAnalyzer - Perform risk assessment and management - Create FortiAnalyzer event handlers |
| Network security | - Configure security inspections for industrial protocols - Configure virtual patching - Configure automation |
>> New NSEI_OTS_AR-7.6 Braindumps Pdf <<
You can also trust Fortinet NSEI_OTS_AR-7.6 exam questions and start Fortinet NSEI_OTS_AR-7.6 exam preparation. With the Fortinet NSEI_OTS_AR-7.6 valid dumps you can get an idea about the format of real Fortinet NSEI_OTS_AR-7.6 Exam Questions. These latest Fortinet NSEI_OTS_AR-7.6 questions will help you pass the Fortinet NSE I - OT Security 7.6 Architect NSEI_OTS_AR-7.6 exam.
NEW QUESTION # 56
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 57
According to the IEC 62443 standard, your security level is 4 . What is your OT environment defending against? (Choose one answer)
Answer: D
Explanation:
Explanation:
NEW QUESTION # 58
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,B
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 59
Refer to the exhibit.
Which statement about this partial Asset Identity List page is correct? (Choose one answer)
Answer: C
Explanation:
The correct answer is B. A firewall policy has a Virtual Patching security profile applied to it .
The decisive clue in the exhibit is the Vulnerabilities column showing KEVs and device-specific vulnerability counts. The study guide explains the virtual patching workflow in this exact way: "FortiGate performs a lookup for device-specific vulnerabilities and mitigation rules in FortiGuard," then
"FortiGuard returns specific OT virtual patching signatures," and "FortiGate caches the signatures and mitigation rules that apply to each device." That is the same behavior reflected by the Asset Identity List showing vulnerability information per detected device.
The guide then states that "When traffic related to the vulnerable device reaches FortiGate, the firewall policy with the virtual patching profile applies." It also says "A virtual patching profile can be applied to firewall policies in any direction, protecting traffic from or to the vulnerable OT device." This directly links the per-device vulnerability visibility to a Virtual Patching profile enforced through firewall policy.
The other options do not match the exhibit. Antivirus is not described in the study guide as building a device- by-device vulnerability list, Application Control is used for OT protocol and message visibility, and IPS focuses on exploit detection and prevention. The Vulnerabilities/KEVs display is the indicator that FortiGate is using Virtual Patching logic for those OT devices.
NEW QUESTION # 60
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: B
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 61
......
Do you feel aimless and helpless when the NSEI_OTS_AR-7.6 exam is coming soon? If your answer is absolutely yes, then we would like to suggest you to try our NSEI_OTS_AR-7.6 training materials, which are high quality and efficiency test tools. Your success is 100% ensured to pass the NSEI_OTS_AR-7.6 Exam and acquire the dreaming certification which will enable you to reach for more opportunities to higher incomes or better enterprises.
NSEI_OTS_AR-7.6 Test Sample Online: https://www.actualpdf.com/NSEI_OTS_AR-7.6_exam-dumps.html