In order to provide you with the best Cisco certification exam dumps forever, ExamsLabs constantly improve the quality of 300-110 exam dumps and update the dumps on the basis of the latest test syllabus at any time. ExamsLabs is your best choice on the market today and is recognized by all candidates for a long time. If you don't believe what I say, you can know the information by asking around. Somebody must have been using ExamsLabs dumps. We assure ExamsLabs provide you with the latest and the best questions and answers which will let you pass the 300-110 Exam at the first attempt.
| Section | Weight | Objectives |
|---|---|---|
| Wireless Site Survey | 25% | - RF propagation and attenuation analysis - Pre-deployment survey and validation - Design requirements collection and constraint evaluation
|
| WLAN High Availability and Security Design | 20% | - Security architecture design
- High availability design
|
| Wireless Infrastructure Design | 30% | - High-density wireless design
|
| Mobility Design | 25% | - Roaming optimization
|
>> Valid 300-110 Test Voucher <<
Challenges are omnipresent everywhere. This challenge of 300-110 practice exam is something you do not need to be anxious with our 300-110 practice materials. If you make choices on practice materials with untenable content, you may fail the exam with undesirable outcomes. Our Designing Cisco Wireless Networks practice materials are totally to the contrary. Confronting obstacles or bottleneck during your process of reviewing, 300-110 practice materials will fix all problems of the exam and increase your possibility of getting dream opportunities dramatically.
NEW QUESTION # 70
A customer purchases this Cisco equipment for a new branch office: ?20 Cisco Catalyst 9120 APs ?five Catalyst 9130 APs ?a single Catalyst 9300 Series Switch The customer wants to extend its existing wired and wireless fabric-enabled network to the branch office and manage all devices via a centrally deployed Cisco Catalyst Center (formerly DNA Center). Which Cisco Catalyst Center licenses are required for the branch office equipment?
Answer: A
Explanation:
Cisco Catalyst Center uses a tiered licensing model -- Essentials and Advantage -- applied to both switching and wireless infrastructure. To enable a fully fabric-enabled (SD-Access) deployment with centralized management, the Cisco Catalyst Advantage license is required across all device types. The Advantage tier unlocks Software-Defined Access fabric capabilities including macro and micro- segmentation, integration with Cisco ISE for policy enforcement, AI/ML-driven analytics via DNA Spaces and Assurance, and automated provisioning. The Essentials license provides only basic device management, inventory, and software image management -- it does not unlock SD-Access fabric functionality. Since the branch design specifically extends an existing fabric-enabled network, the Essentials tier for either the switch or APs would create a licensing gap preventing full fabric participation.
NEW QUESTION # 71
A network engineer must design a new Cisco wireless solution that contains three Cisco 9800-40 WLCs. WLC1 and WLC2 will be combined into one logical unit with SSO and a backup WLC named WLC3 will be joined by using a mobility tunnel. Link redundancy between the WLCs and the switches is required. Which WLCs must the design provide connectivity to the network equipment for LAG to be effective in an SSO failover scenario?
Answer: B
Explanation:
In a Cisco Catalyst 9800 SSO deployment using Link Aggregation Group (LAG) for network interface redundancy, the SSO pair -- WLC1 (active) and WLC2 (standby) -- must both have their physical interfaces connected to the network infrastructure as part of the LAG bundle. LAG on the
9800 in an SSO configuration is implemented as a multi-chassis LAG across both the active and standby controllers. This means both WLC1 and WLC2 contribute physical member links to the port channel, and the connected switches must have LACP or PAgP bundle members from both controllers in the same port channel group. When an SSO failover occurs -- WLC1 fails and WLC2 takes over as active -- the LAG remains operational because WLC2's physical links are already established members of the bundle and continue forwarding traffic without any link renegotiation. If only WLC1 had LAG connectivity and WLC2 had independent links, an SSO failover would cause a LAG topology change requiring re-convergence, introducing downtime.
WLC3 is a separate N+1 backup controller joined via a mobility tunnel -- not part of the SSO pair and its LAG configuration is independent. Reference:
NEW QUESTION # 72
During a validation survey of a newly deployed WLAN, the engineer measures -70 dBm at the cell edge on a data-only WLAN, but the noise floor is -78 dBm. Which conclusion should the engineer reach?
Answer: D
Explanation:
Signal strength alone is an incomplete measure of coverage quality - what determines whether a client can demodulate a frame is how far the signal rises above the surrounding noise. Here the received signal is -70 dBm and the noise floor is -78 dBm, giving a signal-to-noise ratio of only 8 dB. A data WLAN requires a minimum SNR of approximately 20 dB, and voice requires 25 dB, so this location fails validation despite an RSSI value that would otherwise appear acceptable. An elevated noise floor of -78 dBm also points to a non-Wi-Fi interference source or excessive co- channel activity that spectrum analysis should identify, since a clean environment typically sits closer to -90 dBm. The remediation is to address the noise source or increase signal strength through AP placement, not to accept the reading because one of the two metrics passes.
Requiring -60 dBm across all WLANs is far stricter than any Cisco design guidance and would produce an unnecessarily dense and expensive deployment.
NEW QUESTION # 73
An engineer must assess an existing company WLAN to determine the possibility for future IEEE
802.11ac Wave 2 wireless deployment. All access switches are Fast Ethernet-capable only, and the wired infrastructure between existing APs and access switches is based on the CAT 6A standard. Which two actions provide maximum support of Cisco 3800 Series access points?
(Choose two.)
Answer: C,E
Explanation:
Cisco 3800 Series APs support IEEE 802.11ac Wave 2, which can deliver throughput exceeding
1 Gbps. Fast Ethernet switches are limited to 100 Mbps per port, creating a severe bottleneck.
The two actions that provide maximum support are replacing with mGig switches (Option A) and replacing with gigabit switches with 10G uplinks (Option B). mGig (Multi-Gigabit Ethernet) switches support 2.5G and 5G speeds over existing CAT 6A cabling, allowing the full throughput of 802.11ac Wave 2 APs to be utilized without replacing the existing cable plant. Gigabit switches with 10G uplinks ensure that the access layer can support 1 Gbps per AP port while providing sufficient uplink capacity.
NEW QUESTION # 74
An engineer is designing a high-density WLAN that must support 100 concurrent users with 100 Mbps throughput consistently. The design allows for 20 Mbps per cell and per channel on the 5 GHz band. How many channels must the design use to provide 1 Mbps per user prior to RF overhead?
Answer: B
Explanation:
This question requires straightforward wireless capacity engineering calculation. The total throughput requirement is 100 users ?1 Mbps per user = 100 Mbps aggregate. Each channel in the design can support 20 Mbps of usable throughput -- this is the per-cell, per-channel allocation defined in the design parameters, representing usable throughput prior to RF overhead as stated in the question. The number of channels required is: total required throughput divided by throughput per channel = 100 Mbps ?20 Mbps per channel = 5 channels. In practice, each channel corresponds to a non-overlapping frequency assignment in the 5 GHz band. With 5 channels and 20 Mbps per channel, the design provides exactly 100 Mbps of aggregate capacity for 100 concurrent users at 1 Mbps each. This calculation methodology is foundational to Cisco's high-density WLAN design approach, where the number of spatial streams, channel allocations, and AP placement are all derived from the per-user throughput requirement multiplied by the concurrent user population.
NEW QUESTION # 75
......
So many of our worthy customers have achieved success not only on the career but also on the life style due to the help of our 300-110 study guide. You can also join them and learn our 300-110 learning materials. You will gradually find your positive changes after a period of practices. Then you will finish all your tasks excellently. You will become the lucky guys if there has a chance. Our 300-110 Exam Braindumps are waiting for you to have a try.
300-110 Test Questions Fee: https://www.examslabs.com/Cisco/CCNP-Wireless/best-300-110-exam-dumps.html