If you are sure that you want to be better, then you must start taking some measures. Selecting H35-581_V2.0 practice prep may be your key step. If you are determined to pass the exam, our H35-581_V2.0 study materials can provide you with everything you need. You can have the H35-581_V2.0 Learning Materials, study plans and necessary supervision you need. You will have no reason to stop halfway until you get success.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: 5G Radio Network In-depth Principles | 30% | - Massive MIMO and beamforming principles - 5G NR protocol stack and signaling procedures - 5G spectrum and frame structure - 5G NR air interface fundamentals |
| Topic 2: 5G Radio Network Optimization | 20% | - Drive test and signaling tracing - Coverage, capacity, and quality optimization - Fault diagnosis and troubleshooting - Performance indicator analysis |
| Topic 3: 5G RAN Feature Application | 35% | - Mobility management and handover optimization - Carrier aggregation and dual connectivity - Energy saving and coverage enhancement features - Power control and load balancing |
| Topic 4: 5G Industry Applications & Private Network Solutions | 5% | - Private 5G network requirements and design - Vertical industry scenarios and KPI requirements |
| Topic 5: 5G Radio Network Planning | 10% | - Interference analysis and mitigation - Coverage and capacity planning - Parameter planning and configuration - Link budget calculation |
>> H35-581_V2.0 Latest Exam Materials <<
Regular practice can give you the skills and confidence needed to perform well on your H35-581_V2.0 exam. By practicing your HCIP-5G-RNP&RNO V2.0 (H35-581_V2.0) exam regularly, you can increase your chances of success and make sure that all of your hard work pays off when it comes time to take the test. We understand that every HCIP-5G-RNP&RNO V2.0 (H35-581_V2.0) exam taker has different preferences. To make sure that our Huawei H35-581_V2.0 preparation material is accessible to everyone, we made it available in three different formats.
NEW QUESTION # 44
Which SSB pattern cases are supported by Huawei NR TDD base stations?
Select All that Apply
Answer: A,B,D
Explanation:
The intended answers are Case D, Case C, and Case A, corresponding to the SSB transmission patterns identified as supported by the Huawei NR TDD implementation described in the updated question bank.
In 5G NR, Synchronization Signal/PBCH Block (SSB) patterns define the candidate time-domain positions of synchronization blocks within an SSB burst set.
The patterns depend on the SSB subcarrier spacing, operating frequency range, and applicable radio-access configuration.
Case A uses 15 kHz subcarrier spacing and is defined for applicable FR1 operating bands.
Case C uses 30 kHz subcarrier spacing and supports configurations used in applicable low-frequency NR deployments, including TDD bands.
Case D uses 120 kHz subcarrier spacing and is associated with higher-frequency NR operation.
The source material identifies Cases A and C as supported for Huawei low-frequency TDD deployments and Case D for supported high-frequency TDD deployments.
Case B also uses 30 kHz subcarrier spacing and is a valid standardized SSB pattern. Its exclusion here reflects the intended Huawei product-support subset rather than a prohibition imposed by the NR specification.
Therefore, options B, C, and D are the intended answers.
Official Reference: 3GPP TS 38.213, Section 4.1, Cell Search and Candidate SS/PBCH Block Positions ; TS
38.101-1 and TS 38.101-2, applicable band and SSB numerology requirements.
Technical warning / qualification: This is a Huawei software-version-specific question. The standards confirm that Cases A, B, C, and D exist, but do not independently establish the supported subset for every Huawei TDD base-station release. The official Huawei 5G RAN Channel Management Feature Parameter Description for the relevant release is required for final vendor verification.
NEW QUESTION # 45
Which of the following parameters determines the PRACH time-domain position?
Answer: D
NEW QUESTION # 46
In an NSA access issue, which of the following can cause a UE not to report B1 measurement results?
Select All that Apply
Answer: A,B,C,D
Explanation:
All four conditions can prevent a UE from generating or transmitting a valid B1 measurement report during Non-Standalone (NSA) E-UTRA-NR Dual Connectivity (EN-DC) access.
In NSA architecture, the LTE eNodeB acts as the Master Node and configures NR inter-RAT measurements to determine whether an eligible 5G NR cell can be added as a Secondary Node.
Event B1 is triggered when the measured quality of an inter-RAT neighboring cell exceeds the configured threshold, subject to hysteresis and time-to-trigger requirements.
Option A: Excessive received signal power may saturate the UE receiver, degrading synchronization-signal detection and preventing successful NR cell measurements.
Option B: If the LTE-side measurement configuration identifies a frequency that does not correspond to the intended NR SSB carrier, the UE may be unable to detect the target NR synchronization signals.
Option C: If the measured NR signal does not satisfy the configured B1 entry condition, the reporting event is not triggered.
Option D: An abnormal NR cell may fail to transmit the required synchronization signals correctly or provide measurable radio coverage, preventing a valid measurement result.
Therefore, all four conditions are plausible causes of missing B1 measurement reports.
Official Reference: 3GPP TS 36.331, Inter-RAT Measurement Reporting - Event B1 ; TS 38.533, Section
8.4.2, NR Inter-RAT Event-Triggered Reporting Requirements .
NEW QUESTION # 47
Which of the following cause values can be carried in the SCG failure information message?
Select All that Apply
Answer: C,D
Explanation:
Options A and B are correct because both SCG reconfiguration failure and an RLC maximum-retransmission condition are defined failure causes that can be reported through the Secondary Cell Group (SCG) failure information procedure.
In NR Dual Connectivity, the SCG represents the secondary radio resources provided by the Secondary Node.
When an SCG failure occurs, the UE may report the failure to the Master Node without immediately releasing the entire master connection.
Option A - SCG reconfiguration failure: This condition occurs when the UE cannot successfully apply an applicable RRC reconfiguration affecting the SCG. The standardized failure type is scg-reconfigFailure .
Option B - Maximum RLC retransmissions: When the SCG Radio Link Control (RLC) entity reaches its configured maximum retransmission threshold, the UE can initiate SCG failure reporting. The corresponding standardized failure type is rlc-MaxNumRetx .
Option C - T301 timeout: T301 is associated with RRC connection reestablishment. Its expiration is not defined as one of the listed SCG failure types.
Option D - SRB1 integrity check failure: The SCG failure procedure can report an SRB3 integrity failure, not the SRB1 condition specified in this option.
Therefore, A and B are the correct choices.
Official Reference: 3GPP TS 38.331, Section 5.7.3, SCG Failure Information Procedure , and Section 6.2.2, SCGFailureInformation Message and FailureType .
NEW QUESTION # 48
Which of the following PUCCH measurement counters is used for outer-loop power control on PUCCH?
Answer: A
Explanation:
Block Error Rate (BLER) is the intended answer because outer-loop power-control algorithms use error- performance feedback to adjust the target received signal quality required for reliable control-channel reception.
PUCCH carries essential Uplink Control Information (UCI), including HARQ acknowledgments, scheduling requests, and configured channel-state reports.
Errors in these transmissions can produce unnecessary retransmissions, incorrect scheduling decisions, and reduced radio-network efficiency.
The distinction between inner-loop and outer-loop power control is important.
Inner-loop power control adjusts transmission power according to the difference between measured signal quality, commonly expressed through SINR, and a configured target.
The gNodeB can issue Transmit Power Control (TPC) commands to modify the UE's PUCCH transmit power.
Outer-loop power control adjusts the target signal-quality requirement according to observed error performance. When reception reliability deteriorates, the target SINR can be increased to improve decoding probability. Conversely, consistently satisfactory error performance can permit a reduction in the target.
RSRP measures received reference-signal power, while power spectral density expresses signal or noise power per unit bandwidth. Neither directly represents the error-performance feedback used in the intended outer-loop mechanism.
Therefore, BLER is the expected examination answer, with implementation-specific qualifications.
Official Reference: 3GPP TS 38.213, Section 7.2.1, PUCCH Transmit Power Control .
Technical warning / qualification: 3GPP specifies the PUCCH power-control signaling and calculations but does not mandate one universal BLER-based outer-loop algorithm. Huawei implementations may use BER or another error-performance measure depending on the radio technology and PUCCH configuration.
NEW QUESTION # 49
......
You can get a complete new and pleasant study experience with our H35-581_V2.0 exam preparation for the efforts that our experts devote themselves to make. They have compiled three versions of our H35-581_V2.0study materials: the PDF, the Software and the APP online. So you are able to study the online test engine by your cellphone or computer, and you can even study H35-581_V2.0 Exam Preparation at your home, company or on the subway, you can make full use of your fragmentation time in a highly-efficient way.
Exam Discount H35-581_V2.0 Voucher: https://www.test4engine.com/H35-581_V2.0_exam-latest-braindumps.html