あなたの夢は何ですか。あなたのキャリアでいくつかの輝かしい業績を行うことを望まないのですか。きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。IT業種で仕事しているあなたは、夢を達成するためにどんな方法を利用するつもりですか。実際には、IT認定試験を受験して認証資格を取るのは一つの良い方法です。最近、FortinetのNSE7_FSN_AR-7.6試験は非常に人気のある認定試験です。あなたもこの試験の認定資格を取得したいのですか。さて、はやく試験を申し込みましょう。CertJukenはあなたを助けることができますから、心配する必要がないですよ。
| Section | Objectives |
|---|---|
| Enterprise Firewall | - Authentication and identity - High availability - Centralized management and analytics - VPN technologies - Advanced firewall deployment - Security Fabric integration - Troubleshooting - Routing and advanced networking |
| SD-WAN | - Overlay VPN - SD-WAN routing - Performance SLA - SD-WAN architecture - Deployment and troubleshooting - Application steering |
Fortinet NSE7_FSN_AR-7.6認定試験の難しさで近年にほとんどの受験生は資格認定試験に合格しなっかたと良く知られます。だから、我々社の有効な試験問題集は長年にわたりFortinet NSE7_FSN_AR-7.6認定資格試験問題集作成に取り組んだIT専門家によって書いてます。実際の試験に表示される質問と正確な解答はあなたのFortinet NSE7_FSN_AR-7.6認定資格試験合格を手伝ってあげます。
質問 # 35
The local OSPF router is unable to establish adjacency with a peer.
Which two things should the administrator do to troubleshoot the issue? (Choose two.)
正解：A、C
解説：
The correct answers are A and B .
The Network Security Support Engineer 7.6 Study Guide states under OSPF Troubleshooting :
"Follow these steps to troubleshoot an OSPF problem between two peers:
* Check that the local router can reach the remote peer. IP addresses must be in the same subnet and have the same subnet mask.
* Ensure that IP protocol 89 is not blocked.
* Hello and dead intervals must match.
* The OSPF router ID for each peer must be unique. Duplicate router IDs are not allowed.
* Do the MTUs match?
* If authentication is enabled, the type and password must match on both sides."** The same page also summarizes the troubleshooting tips as:
* "Do peers have an IP address within the same subnet?"
* "Is IP protocol 89 blocked?"
This directly confirms:
* A is correct
* B is correct
Why the other options are wrong:
* C is wrong because TCP port 179 is used by BGP , not OSPF. OSPF uses IP protocol 89 , as the study guide explicitly notes
* D is wrong because the study guide's OSPF adjacency troubleshooting checklist does not require an active static route to the peer. OSPF neighbors form adjacency on directly reachable networks, and the guide instead focuses on same subnet, protocol 89, intervals, router ID, MTU, and authentication matching So the verified answers are: A, B .
質問 # 36
Refer to the exhibit, which shows the output of a real-time debug. Which statement about this output is true?
(Choose one answer)
正解：A
解説：
The correct answer is A .
The debug output is for an HTTPS request and shows a hostname value. The study guide explains that with SSL certificate inspection, FortiGate extracts the FQDN from either:
* "TLS extension server name indication (SNI)"
* "SSL certificate common name (CN)"
So the hostname shown in the real-time web-filter debug can be derived from the SNI in the client request or, if needed, from the CN in the server certificate. That makes A correct.
Why the other options are wrong:
* B is wrong because the study-guide example for web-filter real-time debug explicitly says: "This slide shows an example of real-time debug output when the URL to categorize isn ' t in the FortiGuard cache." In these debugs, cat=255 appears before the final lookup result, so this does not indicate a local- cache hit.
* C is wrong because ftgd-allow is the action , not the profile name. The debug line shows the action as action=9 (ftgd-allow) while the profile shown is profile= ' default ' . FortiOS web-filter logs also use the profile field separately from the action field
* D is wrong because the final category shown is url_cat=52 , not 255. The study guide's example shows the same pattern: an initial cat=255 in the request line, followed by the resolved result cat=52 url_cat=52 So the verified answer is: A .
質問 # 37
Refer to the exhibit.
You update the spokes configuration of an existing auto-discovery VPN (ADVPN) topology by adding the parameters shown in the exhibit.
Which is a valid objective of those settings?
正解：A
解説：
The configuration enables network-overlay and assigns a different network-id to each overlay. The SD-WAN
7.6 Enterprise Administrator Study Guide explains that these settings distinguish overlays and prevent shortcut establishment across incompatible overlay networks. Consequently, the valid objective is preventing cross-overlay shortcuts.
The additional auto-discovery-shortcuts dependent setting controls shortcut lifetime: a shortcut is brought down when its parent tunnel goes down. It does not convert an existing ADVPN deployment to ADVPN 2.0.
It also does not prevent multiple legitimate shortcuts from using the same overlay. Although network-overlay enable identifies an IPsec tunnel as an overlay, the combination of network-overlay with distinct network-id values specifically provides overlay separation. Therefore, C is the correct answer.
質問 # 38
Refer to the exhibit, which shows the output o! the BGP database.
Which two statements are correct? (Choose two.)
正解：B、C
解説：
For Option A:In Fortinet BGP (and standard BGP), when a prefix is displayed with an " i " (lowercase i) in the Path column, it represents an internal prefix that originated from the local router, typically configured via the BGP " network " command. In the exhibit, the prefix 10.20.30.0/24 is listed with a Path value of i, indicating it was injected into BGP by the local router using the network statement, not via redistribution from another routing protocol. The same logic applies to i as documented: " Origin code ' i ' means the route was injected via the network command. " For Option D:The get router info bgp network output is a summary table displaying both local and received BGP routes. It lists all known routes to the BGP process, whether received from peers or originated locally.
The exhibit shows all BGP prefixes known to the local router, matching the official admin guide's description of this command's output.
Explanation for B and C:
The phrase "legacy route advertisement" is not formalized in BGP documentation or Fortinet's admin guide; the output uses standard BGP mechanics.
If a route was redistributed into BGP from another routing protocol, the Path field would display a " ? " (question mark) for incomplete (redistributed) origin. Here the /24 route has " i " so it is NOT a redistribution.
References:
FortiOS Administration Guide: BGP Configuration and Route Table Interpretation Official BGP Command Reference: Show BGP Network, Path Codes, Route Origination Indicators
質問 # 39
Refer to the exhibit.
The modified output of live routing kemel is shown
Which two statements about the output are (rue? (Choose two.)
正解：A、B
解説：
We must analyze the flags (*, > , S, O, B) and Administrative Distances (AD) shown in the get router info routing-table database exhibit to determine the correct statements.
Analysis for Option A (The BGP route to 10.0.4.0/24 is not in the forwarding information base):
True. Look at the entry for 10.0.4.0/24.
There is an OSPF route: O * > 10.0.4.0/24 [110/2]. The * indicates it is in the FIB, and > indicates it is the selected route.
There is a BGP route: B 10.0.4.0/24 [200/10]. This line lacks the * flag.
Reason: The OSPF route has an Administrative Distance of 110. The BGP route (iBGP) has an AD of 200.
Since 110 is lower than 200, OSPF wins, and the BGP route is not installed in the Forwarding Information Base (FIB).
Analysis for Option B (The default static route through 10.200.1.254 is in the forwarding information base):
True. Look at the 0.0.0.0/0 entries.
The first entry is S * > 0.0.0.0/0 [10/0] via 10.200.1.254.
The * flag confirms this specific route is installed in the FIB.
The second static route (via 10.200.2.254) has a higher distance ([20/0]) and no * flag, so it is inactive.
Why C is False: ECMP (Equal Cost Multi-Path) requires routes to have the same cost/priority. Here, one static route has AD 10 and the other has AD 20. They are not equal, so ECMP is not performed.
Why D is False: The routing table database shows active routes, not the raw Link State Advertisement (LSA) database. You cannot determine the number of LSAs received solely from this output.
Reference:
FortiGate Security 7.6 Study Guide (Routing): " The routing table database displays all known routes... The * indicates the route is in the FIB... Lower Administrative Distance is preferred. "
質問 # 40
......
NSE7_FSN_AR-7.6学習教材は、国際市場で非常に人気があり、サークル内外の人々から幅広い賞賛を受けています。 NSE7_FSN_AR-7.6試験問題を有名でトップランクのブランドに作り上げました。クライアントからは当然の評判を得ています。 NSE7_FSN_AR-7.6学習教材は、他の同じ種類の製品にはない多くの優れた優れた利点を後押しします。クライアントは、CertJuken購入前にFortinet NSE 7 - Secure Networking 7.6 Architect教材を試用してダウンロードできます。支払いが完了したら、すぐにNSE7_FSN_AR-7.6トレーニングガイドを使用できます。
NSE7_FSN_AR-7.6関連資格知識: https://www.certjuken.com/NSE7_FSN_AR-7.6-exam.html