IT인증시험은 국제적으로 인정받는 자격증을 취득하는 과정이라 난이도가 아주 높습니다. Versa Networks인증 VNX301시험은 IT인증자격증을 취득하는 시험과목입니다.어떻게 하면 난이도가 높아 도전할 자신이 없는 자격증을 한방에 취득할수 있을가요? 그 답은DumpTOP에서 찾을볼수 있습니다. DumpTOP에서는 모든 IT인증시험에 대비한 고품질 시험공부가이드를 제공해드립니다. DumpTOP에서 연구제작한 Versa Networks인증 VNX301덤프로Versa Networks인증 VNX301시험을 준비해보세요. 시험패스가 한결 편해집니다.
| Section | Objectives |
|---|---|
| High Availability and Redundancy | - HA active-active and failover design - Redundant gateway and link resiliency |
| Policy-Based Routing and Traffic Steering | - Path selection and SLA-based steering - Application-aware routing policies |
| QoS and Performance Optimization | - QoS/CoS configuration - Latency, jitter, and bandwidth optimization |
| Versa SD-WAN Platform Components | - Versa Controller, Director, Analytics roles - VOS components and CPE devices |
| SD-WAN Fundamentals and Architecture | - Underlay and overlay network design - SD-WAN principles and architecture concepts |
| Security and Encryption | - Encryption and certificate management - Firewall policies and security services |
| Deployment and Provisioning | - Branch and edge deployment models - ZTP and onboarding workflows |
| Monitoring, Analytics and Troubleshooting | - Troubleshooting SD-WAN performance issues - Versa Analytics dashboards |
많은 사이트에서 Versa Networks인증 VNX301시험대비덤프를 제공해드리는데DumpTOP를 최강 추천합니다. DumpTOP의Versa Networks인증 VNX301덤프에는 실제시험문제의 기출문제와 예상문제가 수록되어있어 그 품질 하나 끝내줍니다.적중율 좋고 가격저렴한 고품질 덤프는DumpTOP에 있습니다.
질문 # 42
Which two statements are true about templates? (Choose two.)
정답：C,D
설명：
The correct answers are C and D . Versa templates are designed to reuse common configuration while still allowing per-device customization. Template variables allow the same template to be deployed to multiple appliances while using device-specific values such as addresses, VLAN IDs, DHCP information, or other bind-data values. Versa documentation for deploying templates describes assigning values to variables contained in a main template that are specific to the device. This makes option C correct.
Option D is also correct because Versa workflows are used to create templates for VOS device configuration.
Versa documentation states that workflows are used to create templates to configure VOS devices, and also to create templates for application steering, spoke groups, and service chains.
Option A is not correct in the normal Versa Director onboarding model because a group of devices is associated with one staging template and one post-staging template, rather than multiple device templates being stacked per appliance. Option B is also incorrect because service templates are optional reusable service-specific fragments. Versa documentation states that service templates can be used by multiple device templates and device groups, but it does not require every appliance to have one.
질문 # 43
During branch onboarding, you need to verify whether the Controller has sent branch-connect and branch- disconnect notifications to Versa Director. Which CLI command should be used?
정답：B
설명：
The correct answer is A . Versa troubleshooting documentation states that after a branch device successfully establishes an IPsec connection to the Controller node, the Controller sends a notification to the Director node. To display the details of this notification, the documentation instructs administrators to issue the show alarms CLI command. It also provides examples using show alarms | match branchd | match br101 to view branch-connect and branch-disconnect events.
These alarm entries are valuable during onboarding because they show whether the branch reached the Controller, whether staging progressed, and whether the branch later disconnected. For example, branch lifecycle notifications include factory-default connection, staged connection, Stage 3 connection with WAN IP addresses, and branch disconnect events.
show system storage is useful for disk usage, show interfaces detail helps with link state, speed, duplex, and interface counters, and show cgnat acl info is used for CGNAT matching. None of those commands directly confirms branch lifecycle notifications between Controller and Director.
질문 # 44
A branch user reports poor throughput over an SD-WAN tunnel. The command show interfaces detail vni-0/0 shows the interface is operating at half-duplex / 100 Mbps , although the circuit is expected to run at 1 Gbps full duplex. What is the most likely cause?
정답：C
질문 # 45
While troubleshooting the SD-WAN data path, you run show vsf tunnel access-circuits ... detail and see the following encapsulation chain: VMLH, MPLS-over-GRE, IPsec-ESP, and VXLAN. What does this output primarily confirm?
정답：B
설명：
The correct answer is B . Versa's SD-WAN data-path troubleshooting documentation shows that show vsf tunnel access-circuits ... detail can display the access-circuit state and encapsulation chain used for tunnel forwarding. In the example, the output lists multiple encapsulations, including VMLH , MPLS-over-GRE , IPsec-ESP , and VXLAN . It also shows transport details such as source IP, destination IP, UDP transport, tunnel MTU, SPI values, and SLA state.
This confirms that the VOS data plane has built the SD-WAN tunnel encapsulation stack required to forward overlay traffic across the underlay. IPsec-ESP in the chain indicates encrypted tunnel handling, while VXLAN and other encapsulation components are part of the SD-WAN overlay forwarding structure.
The output does not indicate simple bridging, plain-text-only GRE, or bypass of the VOS data plane.
Instead, it proves that the packet path is being processed through the VOS tunnel forwarding framework and that the administrator is looking at the SD-WAN access-circuit tunnel state.
질문 # 46
A branch user reports poor throughput over an SD-WAN tunnel. The command show interfaces detail vni-0/0 shows the interface is operating at half-duplex / 100 Mbps , although the circuit is expected to run at 1 Gbps full duplex. What is the most likely cause?
정답：C
설명：
The correct answer is C . Versa's bandwidth and throughput troubleshooting documentation specifically instructs administrators to check link speed and half-duplex conditions with the command show interfaces detail interface-name. The example output shows an interface operating at half-duplex / 100 Mbps , and the documentation states that the interface should not be in half-duplex mode and that 100 Mbps was incorrect in that scenario.
A duplex mismatch or incorrect negotiated speed can severely reduce effective throughput, cause collisions or retransmissions, and make SD-WAN overlay performance appear poor even when the overlay itself is functioning. Versa recommends fixing half-duplex and link-speed issues by correcting the configuration on the device to which the VOS device is connected and checking the ISP-side transmission mode, such as auto
/auto.
SLA probing, Controller route advertisement, and VXLAN encapsulation may affect SD-WAN path selection or tunnel formation, but the evidence in the question directly points to a physical or underlay Ethernet negotiation problem.
질문 # 47
......
DumpTOP의 Versa Networks VNX301덤프는 Versa Networks VNX301시험문제변경에 따라 주기적으로 업데이트를 진행하여 덤프가 항상 가장 최신버전이도록 업데이트를 진행하고 있습니다.구매한 Versa Networks VNX301덤프가 업데이트되면 저희측에서 자동으로 구매시 사용한 메일주소에 업데이트된 최신버전을 발송해드리는데 해당 덤프의 구매시간이 1년미만인 분들은 업데이트서비스를 받을수 있습니다.
VNX301시험패스 인증공부: https://www.dumptop.com/Versa-Networks/VNX301-dump.html