BONUS!!! Download part of ExamsReviews 300-425 dumps for free: https://drive.google.com/open?id=1e9iU3vnKnSadPckZDnccHsQfNyy8wOwp
The web-based 300-425 practice exam is similar to the desktop-based software. You can take the web-based 300-425 practice exam on any browser without needing to install separate software. In addition, all operating systems also support this web-based Cisco 300-425 Practice Exam. Both Designing Cisco Enterprise Wireless Networks practice exams track your performance and help to overcome mistakes. Furthermore, you can customize your Designing Cisco Enterprise Wireless Networks practice exams according to your needs.
| Section | Weight | Objectives |
|---|---|---|
| Wired and Wireless Infrastructure Design | 30% | - Logical infrastructure
|
| Mobility Design | 25% | - Roaming and mobility groups
|
| Wireless Site Survey | 25% | - Survey types and execution
|
| WLAN High Availability | 20% | - AP and service redundancy
|
The Designing Cisco Enterprise Wireless Networks exam is one of the most valuable certification exams. The Cisco Designing Cisco Enterprise Wireless Networks exam opens a door for beginners or experienced ExamsReviews professionals to enhance in-demand skills and gain knowledge. 300-425 Exam credential is proof of candidates' expertise and knowledge. After getting success in the Cisco Designing Cisco Enterprise Wireless Networks exam, candidates can put their careers on the fast route and achieve their goals in a short period of time.
NEW QUESTION # 90
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
Answer: B,E,F
Explanation:
For an effective office site survey, it's recommended to: A. Use a battery pack to power APs - This allows for mobility and testing in various locations without relying on fixed power sources. B. Use a drawing of the office space to mark AP and client placements - This helps in planning the optimal locations for AP installation. F. Use APs with built-in antennas - They are commonly used for site surveys as they represent the typical deployment scenario.
Reference:
https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/8-4/b_mesh_84/Site_Preparation_and_Planning.html#ID3405
NEW QUESTION # 91
Which of the following statements best describes the purpose of ARP with respect to CEF?
Answer: D
Explanation:
Address Resolution Protocol (ARP) is used by Cisco Express Forwarding (CEF) to build the adjacency table.
CEF is the switching method used by Catalyst switches. Unlike traditional multilayer switching (MLS), which merely caches Layer 3 information received when traffic passes through a switch, CEF attempts to optimize the routing process by reindexing the routing table and then building an adjacency table based on the routing table information. The type of MLS performed by CEF is called topology-based switching; traditional MLS is known as route caching, demand-based switching, and flow-based switching.
The routing table is reindexed by using a binary search method. The reindexed routing table is called the forwarding information base (FIB). Reindexing the routing table reduces the amount of time spent searching for an entry within a routing table.
After the FIB is created, an adjacency table is created to map the appropriate Layer 2 next-hop address or addresses to each FIB entry. ARP is used to retrieve the Layer 2 address information. If multiple Layer 2 next- hop addresses are available for an entry in the FIB, then CEF can employ load balancing for packets headed to that destination.
The final result is a single database of routing information (FIB) is built for the switching hardware.
Two extremely useful commands for verifying CEF are:
show ip cef network address - displays entries in the forwarding information base (FIB) show adjacency detail | begin adjacency address - shows information about a specific adjacency in the adjacency table Both commands are shown below with explanations.
SwitchA# show ip cef 192.168.6.0
192.168.6.0/24, version 302, cached adjacency 192.168.166.5, 0 packets, 0 bytes Via 192.168.166.5, VLAN 185, 0 dependencies Next-hop 192.168.166.5, VLAN 185 Valid cached adjacency Above it can be determined that there is a valid CEF entry for the destination network 192.168.6.0 and that there is a valid cached adjacency to the 192.168.166.5 next hop IP address.
In the command output below, it can be determined that 005565946856 is the MAC address of the
192.168.166.5 next-hop address:
SwitchA# show adjacency detail | begin 192.168.166.5
IP VLAN 185 192.168.166.5(6) 0 packets, 0 bytes
005565946856
Objective:
Layer 2 Technologies
Sub-Objective:
Configure and verify switch administration
References:
Cisco > Cisco IOS IP Switching Configuration Guide, Release 12.4 > Part 1: Cisco Express Forwarding > Cisco Express Forwarding Overview > Cisco Express Forwarding Adjacency Tables Overview Cisco > Cisco IOS IP Switching Command Reference > show adjacency through show ipv6 cef with source > show adjacency Cisco > Cisco IOS IP Switching Command Reference > show adjacency through show ipv6 cef with source > show ip cef
NEW QUESTION # 92
An engineer must identify the network requirements for a company that has a main office and 10 branch offices. The network must be able to support data, voice, video, and location tracking.
Which two factors must be considered? (Choose two.)
Answer: A,B
Explanation:
When identifying network requirements, it's important to consider the number of wireless devices that will need access to ensure sufficient capacity and coverage. The business type can influence the types of applications and services that will be used, which in turn affects the network design.
NEW QUESTION # 93
An engineer is designing a solution where guests terminate on an anchor controller in the DMZ. The engineer is having issues and wants to test connectivity between members of a mobility group. Which command must be issued to test whether a mobility control packet is able to be reached over the management interface?
Answer: A
Explanation:
The 'tracert' command is used to test connectivity between members of a mobility group by tracing the path that mobility control packets take over the network. This command helps identify any potential issues with the route that the packets are taking, which could affect the ability of guests to connect to the anchor controller in the DMZ. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI
300-430 Official Cert Guide Premium Edition and Practice)
NEW QUESTION # 94
A technician connects a Cisco Aironet 3700 Series access point to a switch and realizes that the AP is coming up with 3x3 MIMO. Which reason explains this behavior?
Answer: C
Explanation:
NEW QUESTION # 95
......
Our 300-425 practice tests have established impressive recognition throughout the industry, diversified modes of learning enables the 300-425 exam candidates to capture at the real exam scenario. Tremendous quality of our 300-425 products makes the admirable among the professionals. Our practice tests are on demand, attending the needs of 300-425 Exams more comprehensively and dynamically as well. Lift up your learning tendency with ExamsReviews practice tests training. Conceptual understanding matters the most for your success, technical excellence is certain with ExamsReviews training as our experts keep it on high priority.
Latest 300-425 Exam Duration: https://www.examsreviews.com/300-425-pass4sure-exam-review.html
DOWNLOAD the newest ExamsReviews 300-425 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=1e9iU3vnKnSadPckZDnccHsQfNyy8wOwp