NSE7_FSN_AR-7.6 Lerntipps & NSE7_FSN_AR-7.6 Originale Fragen

DeutschPrüfung ist eine Website, die alle Ihrer Bedürfnisse zur Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung abdecken kann. Mit den Prüfungsmaterialien von DeutschPrüfung können Sie die Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung mit einer ganz hohen Note bestehen.

Fortinet NSE7_FSN_AR-7.6 Exam Syllabus Topics:

SectionObjectives
Topic 1: Enterprise Firewall- Routing and advanced networking
- Centralized management and analytics
- Authentication and identity
- Advanced firewall deployment
- Security Fabric integration
- VPN technologies
- Troubleshooting
- High availability
Topic 2: SD-WAN- Performance SLA
- Application steering
- SD-WAN architecture
- Overlay VPN
- SD-WAN routing
- Deployment and troubleshooting

>> NSE7_FSN_AR-7.6 Lerntipps <<

NSE7_FSN_AR-7.6 Originale Fragen, NSE7_FSN_AR-7.6 Prüfungsfragen

Wenn wir am Anfang die Fragenkataloge zur Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung bieteten, haben wir niemals geträumt, dass wir so einen guten Ruf bekommen können. Wir geben Ihnen die unglaubliche Garantie. Wenn Sie die Produkte von DeutschPrüfung für Ihre Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung benutzen, versprechen wir Ihnen, die Prüfung 100% zu bestehen.

Fortinet NSE 7 - Secure Networking 7.6 Architect NSE7_FSN_AR-7.6 Prüfungsfragen mit Lösungen (Q121-Q126):

121. Frage
Exhibit.

Refer to the exhibit, which shows the output of get system ha status.
NGFW-1 and NGFW-2 have been up for a week.
Which two statements about the output are true? (Choose two.)

Antwort: B,D

Begründung:
FortiGate HA Troubleshooting and Synchronization Guides
Fortinet Admin Guide: HA Primary Role Retention, Cluster Break-up Due to Out-of-Sync Status


122. Frage
What can cause an IKEv2 tunnel to go down after it was initially brought up successfully?

Antwort: D

Begründung:
The correct answer is A.
The study guide explains the IKEv2 exchange order very clearly:
"The initial exchanges are: IKE_SA_INIT and IKE_AUTH."
"Create_Child_SA exchange: Creates a new child SA or rekeys an existing child SA." It also states:
"After successful IKE_SA_INIT and IKE_AUTH exchanges, the CHILD_SA exchange takes place. In this exchange, the peers negotiate the CHILD_SA and the traffic selectors - traffic selector responder (TSr) and traffic selector initiator (TSi)." That is why A is correct: if the tunnel was initially brought up successfully, then the initial exchanges already succeeded. A later problem during CREATE_CHILD_SA, especially with traffic selectors/phase 2 selectors, can cause the tunnel to fail during rekey or child-SA renegotiation.
Why the other options are wrong:
B is wrong because proposal mismatch for the IKE SA is handled during IKE_SA_INIT, not after the tunnel is already up. The study guide says IKE_SA_INIT negotiates the security settings to protect the IKE traffic C is wrong because a pre-shared key mismatch is part of authentication and would prevent successful initial establishment during IKE_AUTH. The study guide shows that after IKE_AUTH, "authentication succeeded" and "established IKE SA" when it works D is wrong because a Diffie-Hellman mismatch belongs to IKE_SA_INIT, which happens before the tunnel comes up. The study guide also states: "By IKEv2 design, no Diffie-Hellman public key is exchanged during an IKE_AUTH exchange." So the verified answer is: A.


123. Frage
Refer to the exhibit.

A network topology and a partial routing table are shown.
FortiGate has already been configured with a firewall policy that allows all ICMP traffic to flow from port1 to port3.
Which two changes can the administrator perform to ensure the server at 10.4.0.1/24 receives the ICMP echo reply from the laptop at 10.1.0.1/24? (Choose two.)

Antwort: B,C

Begründung:
The correct answers are A and C.
The study guide describes this exact asymmetric ICMP scenario. It states:
"The server sends an echo request to the PC through port2 of the local router, effectively bypassing FortiGate.
When it receives the echo request, the PC responds with an echo reply through its default gateway, 10.1.0.2, which is port1 on FortiGate. Because there is no existing session, the echo reply is dropped. All subsequent echo replies are blocked." That means the current problem exists because:
the ICMP request bypasses FortiGate
the ICMP reply goes through FortiGate
FortiGate has no matching session, so it drops the reply
The study guide then shows the exact corrective option:
"Allowing asymmetric routing:"
config system settings
set asymroute enable
end
It further explains:
"After the packet passes through the FortiGate CPU, FortiGate forwards the packet using the FIB, even though there are no session matches. FortiGate forwards all subsequent echo replies using the FIB." So A is correct.
The other valid fix is to make the traffic symmetric by changing the laptop's default gateway so the reply no longer goes through FortiGate. In the exhibit, the alternate gateway is 10.1.0.254, which is the local router on the same subnet. If the laptop uses 10.1.0.254 instead of 10.1.0.2, the ICMP echo reply follows the same bypass path as the echo request, so the server receives it without involving FortiGate session validation. This makes C correct.
Why the other options are wrong:
B is wrong because this is not an RPF problem. The study guide explains RPF as a reverse path lookup used to validate whether a packet arrived on a legitimate interface, mainly for spoofing protection. The issue in this scenario is a missing session due to asymmetric routing, not a strict-versus-feasible RPF failure D is wrong because FortiGate already has the specific route 10.4.0.0/24 through port3 in the routing table shown in the exhibit, so adding a default static route to port3 is unnecessary and not the reason the echo reply is being dropped So the verified answers are: A, C.


124. Frage
Refer to the exhibit.

A partial output of diagnose npu up6 port-list on FortiGate 2000E is shown.
An administrator is unable to analyze traffic flowing between port1 and port17 using the diagnose sniffer command.
Which two commands allow the administrator to view the traffic? (Choose two.)

Antwort: C,D

Begründung:
The administrator cannot see traffic in the sniffer because it is being offloaded to the NPU (NP6). To view the traffic, offloading must be disabled so packets pass through the CPU.
B). config firewall policy ... set auto-asic-offload disable: This is the recommended method to troubleshoot specific traffic. By disabling ASIC offloading in the relevant firewall policies (Policies 5 and 17 in the exhibit), traffic is forced to the CPU and becomes visible to the sniffer.
C). diagnose npu np6 fastpath disable 1: This command temporarily disables the fastpath processing on the specific NP6 processor (ID 1) handling the ports. This forces all traffic handled by that NPU to the CPU, allowing the sniffer to capture it.
Incorrect Options: Option A uses invalid syntax (port-list disable is not a valid command). Option D (config system npu) is not the standard method for granular troubleshooting.


125. Frage
Refer to the exhibit.

The health-check configuration on a FortiGate device used as a spoke is shown.
You notice that the hub FortiGate does not prioritize the traffic as expected.
Which two configuration elements should you check on the hub? (Choose two.)

Antwort: A,B

Begründung:
Comprehensive and Detailed 100 to 150 words of Explanation From Secure Networking Architect Study Guides topics:
The spoke configuration enables embed-measured-health, which causes SD-WAN SLA status to be embedded in ICMP probes sent toward the hub. For the hub to use this information correctly, Fortinet requires a remote- mode health check and appropriate IKE-route priorities.
The SD-WAN 7.6 Enterprise Administrator Study Guide states that the hub must define priority-in-sla and priority-out-sla, so B is correct. It also explicitly requires the same link-cost factor and metric on the spoke and hub when remote detection is used. In this exhibit, the spoke evaluates latency with a threshold of 100, making the matching SLA criteria on the hub essential and A correct. The hub does not need identical member identifiers because its local SD-WAN members are independently defined. set embedded-measure accept is not the required FortiOS hub configuration for receiving embedded SLA information.


126. Frage
......

Sie können im Internet teilweise die Fragenkatalogen zur Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung von DeutschPrüfung kostenlos herunterladen. Dann werden Sie mehr Vertrauen in unsere Produkte haben. Sie können sich dann gut auf Ihre Fortinet NSE7_FSN_AR-7.6 Zertifizierungsprüfung vorbereiten. Schicken bitte schnell die Produkte von DeutschPrüfung in den Warenkorb.

NSE7_FSN_AR-7.6 Originale Fragen: https://www.deutschpruefung.com/NSE7_FSN_AR-7.6-deutsch-pruefungsfragen.html