BONUS！！！ MogiExam EDGE-Expertダンプの一部を無料でダウンロード：https://drive.google.com/open?id=1IEBzlRIEczmPkwCYrvL2AWoMKeY4DjUD
IT技術人員にとって、両親にあなたの仕事などの問題を危ぶんでいきませんか？高い月給がある仕事に従事したいですか？美しい未来を有したいですか？だから、我々MogiExamのEDGE-Expert問題集をご覧になってください。ここでは、あなたは一番質高い資料と行き届いたサービスを楽しみしています。あなたはMogiExamのEDGE EDGE-Expert問題集を手に入れる前に、問題集の試用版を無料に使用できます。
| Section | Objectives |
|---|---|
| Resource Efficiency Metrics | - Materials efficiency and embodied energy basics - Energy efficiency concepts and savings calculation - Water efficiency strategies and benchmarks |
| Certification Process | - Verification and audit process - Project registration and documentation requirements |
| EDGE Green Building Fundamentals | - Sustainable design principles - Overview of EDGE system and certification framework |
| EDGE Software Application | - Project modeling and inputs in EDGE software - Interpreting performance results and compliance |
EDGE-Expert試験にすばやく合格できるようにする必要があるため、信頼できる製品を選択する必要があります。 EDGE-Expert試験の教材は当局によって認定されており、ユーザーによってテストされています。これは間違いなく自信を持って使用できる製品です。もちろん、私たちのデータはあなたをもっと安心させるかもしれません。 EDGE-Expert準備準備の合格率は99％に達しました。これは非常に信じられない価値ですが、私たちはそれを行いました。製品について詳しく知りたい場合は、スタッフに相談するか、EDGE-Expert練習エンジンの無料試用版をダウンロードしてください。ご参加をお待ちしております。
質問 # 90
A building is located in a hot and dry climate where water availability (rainfall) is low. Which of the following measures will give the lowest water savings?
正解：C
解説：
In a hot and dry climate with low rainfall, water efficiency measures in EDGE are evaluated based on their potential to reduce potable water demand, but their effectiveness depends on local conditions. The EDGE User Guide explains the impact of various water-saving measures: "In regions with low rainfall, rainwater harvesting provides minimal water savings due to limited precipitation, whereas measures like low-flow showers, dual flush toilets, and black water recycling can achieve consistent savings by reducing direct water use or reusing wastewater" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Option B, rainwater harvesting, relies on rainfall to collect water for non-potable uses, but in a hot and dry climate with low water availability, its effectiveness is limited: "Rainwater harvesting systems in EDGE are modeled based on local precipitation data. In arid climates with annual rainfall below 200 mm, savings from rainwater harvesting are typically less than 5% of total water demand, as the collected volume is insufficient to meet significant needs" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). In contrast, Option A (low-flow showers) reduces water use directly: "Low-flow showers can reduce water consumption by 20-30% in buildings, regardless of climate, by limiting flow rates to 6-8 liters per minute" (EDGE User Guide, Section
5.2: Water Efficiency Measures). Option C (recycle black water) also offers consistent savings: "Black water recycling systems can save 30-40% of water demand by treating and reusing wastewater for flushing or irrigation, independent of rainfall" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). Option D (dual flush for water closets) similarly provides reliable savings: "Dual flush toilets reduce water use by 25-35% by offering a low-flush option for liquid waste, effective in all climates" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Given the low rainfall in a hot and dry climate, rainwater harvesting (Option B) yields the lowest water savings compared to the other measures, which do not depend on precipitation. The EDGE User Guide further notes: "In dry climates, measures like rainwater harvesting are often the least effective, while demand-side measures (e.g., low-flow fixtures) and recycling systems provide higher and more consistent water savings" (EDGE User Guide, Section 5.3: Additional Water Efficiency Measures). Thus, rainwater harvesting (Option B) gives the lowest water savings in this context.
Reference:EDGE User Guide Version 2.1, Section 5.2: Water Efficiency Measures, Section 5.3: Additional Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations.
質問 # 91
Which of the following measures will impact energy, water, and materials in an air-conditioned hospital with a water-cooled chiller?
正解：C
解説：
In EDGE, measures are evaluated for their impact on energy, water, and embodied energy in materials, the three core pillars of the standard. For an air-conditioned hospital with a water-cooled chiller, the measure must affect all three areas to be the correct answer. The EDGE User Guide provides detailed descriptions of each measure's impact: "Variable speed drive (VSD) pumps in HVAC systems, such as those used in water- cooled chillers, impact energy by reducing electricity consumption through load modulation, water by optimizing the chiller's cooling water circulation (reducing water use in the cooling tower), and materials because their installation may involve additional components with embodied energy, such as the VSD unit itself" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option C, variable speed drive pumps, thus impacts all three areas: energy (reduced electricity use), water (less cooling tower water loss), and materials (embodied energy in the VSD equipment). Option A (insulation of the roof) affects energy (reduced cooling load) and materials (embodied energy in insulation), but not water: "Roof insulation reduces energy demand but does not directly impact water consumption" (EDGE User Guide, Section 4.1: Insulation Measures). Option B (water-efficient urinals) impacts water (reduced consumption) and potentially materials (embodied energy in fixtures), but not energy: "Water-efficient urinals save water but have no direct energy impact in EDGE calculations" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Option D (water- efficient dishwashers) also affects water and materials, but not energy in this context: "Water-efficient dishwashers reduce water use, but their energy impact is minimal unless they include hot water savings, which is not specified for hospital dishwashers in EDGE" (EDGE Methodology Report Version 2.0, Section
4.2: Water Savings Calculations). The EDGE Methodology Report further confirms: "VSD pumps in water- cooled chillers are unique in affecting all three EDGE metrics-energy through efficiency, water through reduced cooling tower evaporation, and materials through the embodied energy of the equipment" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Thus, variable speed drive pumps (Option C) is the measure impacting energy, water, and materials.
Reference:EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures, Section 4.1: Insulation Measures, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.1:
Energy Efficiency Metrics, Section 4.2: Water Savings Calculations.
質問 # 92
Which of the following heating systems uses Coefficient of Performance (COP) as a measure of efficiency in the EDGE software?
正解：C
解説：
In EDGE, the Coefficient of Performance (COP) is used to measure the efficiency of heating systems that produce heat using a refrigeration cycle, such as heat pumps. The EDGE Methodology Report specifies: "The Coefficient of Performance (COP) is used in EDGE to evaluate the efficiency of heat pumps, including ground source heat pumps, where it is defined as the ratio of thermal output to electrical input. This metric is not applied to direct heating systems like electric heaters or boilers" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Option C, ground source heat pump, fits this description as it operates using a refrigeration cycle to transfer heat, and its efficiency is measured by COP in EDGE. Option A (electric heater) has an efficiency typically measured as 100% (or COP of 1), but EDGE does not use COP for such systems, as noted: "Electric heaters are assumed to have a fixed efficiency in EDGE, not evaluated via COP" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option B (condensing boiler) uses thermal efficiency (%), not COP, as per: "Boilers in EDGE are assessed by their thermal efficiency, not COP" (EDGE Methodology Report Version 2.0, Section 5.2: Heating Systems). Option D (sensible heat recovery from exhaust air) is a heat recovery method, not a heating system, and does not use COP: "Heat recovery systems are evaluated by their heat recovery effectiveness, not COP" (EDGE User Guide, Section 4.3:
Ventilation Measures). Thus, ground source heat pump (Option C) is the correct choice.
Reference: EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics, Section 5.2:
Heating Systems; EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures, Section 4.3:
Ventilation Measures.
質問 # 93
Who are licensed to train candidates as EDGE Experts and EDGE Auditors?
正解：A
解説：
Training for EDGE Experts and Auditors is a structured process managed by specific entities authorized by the IFC. The EDGE Expert and Auditor Protocols specify: "EDGE Faculty are licensed by IFC to deliver training for candidates aspiring to become EDGE Experts and EDGE Auditors. These trainers are selected and trained by IFC to ensure consistency and quality in the delivery of EDGE training programs" (EDGE Expert and Auditor Protocols, Section 3.2: Training Requirements). Option A, EDGE Faculty, directly matches this description. Option B (EDGE Auditors) is incorrect, as auditors perform audits, not training, per the protocols: "EDGE Auditors are responsible for verifying project compliance, not for training others" (EDGE Expert and Auditor Protocols, Section 2.2: Roles). Option C (EDGE Certification Providers) is also incorrect, as their role is to issue certifications, not conduct training: "Certification Providers like GBCI issue EDGE certificates but do not train candidates" (EDGE Certification Protocol, Section 1.3: Certification Process).
Option D (Accredited EDGE Experts) is wrong, as Experts advise on projects, not train others, as per the protocols: "EDGE Experts provide consultancy services to project teams" (EDGE Expert and Auditor Protocols, Section 2.1: Roles).
Reference:EDGE Expert and Auditor Protocols, Section 3.2: Training Requirements, Section 2.1: Roles, Section 2.2: Roles; EDGE Certification Protocol, Section 1.3: Certification Process.
質問 # 94
In the EDGE software, what is the unit of the embodied carbon of the material?
正解：B
解説：
Embodied carbon in EDGE refers to the carbon emissions associated with the production, transportation, and installation of building materials, a key metric for materials efficiency. The EDGE User Guide specifies how this is measured: "In the EDGE software, the embodied carbon of materials is quantified in kilograms of carbon dioxide equivalent (kgCO2), reflecting the total greenhouse gas emissions associated with the material' s lifecycle, from extraction to installation"(EDGE User Guide, Section 7.2: Materials Efficiency Measures).
Option A, kgCO2, directly matches this unit, as EDGE uses kgCO2 to standardize carbon emissions across materials, allowing for comparison and aggregation in the software's results. Option B (MJ) is incorrect, as MJ (megajoules) measures embodied energy, not carbon: "Embodied energy in EDGE is measured in MJ, representing the energy consumed in material production, while embodied carbon is separately calculated in kgCO2 to assess environmental impact" (EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials). Option C (BTU) is also incorrect, as BTU (British Thermal Units) is an energy unit not used in EDGE for carbon calculations: "EDGE uses metric units like MJ for energy and kgCO2 for carbon; BTU is not a standard unit in the software" (EDGE User Guide, Section 2.3: Using the EDGE App). Option D (kWh) is another energy unit, typically used for operational energy, not embodied carbon: "kWh is used in EDGE to measure operational energy consumption, such as electricity use, but not for embodied carbon, which is always in kgCO2" (EDGE Methodology Report Version 2.0, Section 5.2: Energy Calculation Methods). The EDGE User Guide further clarifies: "The software displays embodied carbon in kgCO2 to align with global carbon accounting standards, enabling users to understand the environmental footprint of their material choices" (EDGE User Guide, Section 7.2: Materials Efficiency Measures). The EDGE Methodology Report adds: "For example, concrete might have an embodied carbon of 0.15 kgCO2 per kg, allowing users to compare materials like fly ash concrete versus standard concrete in terms of carbon impact" (EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials). Thus, the unit of embodied carbon in EDGE is kgCO2 (Option A).
Reference:EDGE User Guide Version 2.1, Section 7.2: Materials Efficiency Measures, Section 2.3: Using the EDGE App; EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials, Section
5.2: Energy Calculation Methods.
質問 # 95
......
理論の最新の発展に従って、EDGE-Expert練習教材が多くの専門家によって改訂されることを保証し、学生向けにカスタマイズされた学習コンテンツを専門的にMogiExam編集します。つまり、EDGE-Expert試験を簡単かつ効率的に見つけることができます集中し、良い学術的成果を得る。さらに、EDGE-Expert試験ガイドは、お客様にサプリメントサービスモックテストを提供します。これにより、お客様はEDGE-Expert試験問題を勉強することにより、一生懸命勉強し、欠陥をチェックできます。
EDGE-Expert日本語資格取得: https://www.mogiexam.com/EDGE-Expert-exam.html
P.S. MogiExamがGoogle Driveで共有している無料かつ新しいEDGE-Expertダンプ：https://drive.google.com/open?id=1IEBzlRIEczmPkwCYrvL2AWoMKeY4DjUD