지금21세기 IT업계가 주목 받고 있는 시대에 그 경쟁 또한 상상할만하죠, 당연히 it업계 중Cisco 300-110인증시험도 아주 인기가 많은 시험입니다. 응시자는 매일매일 많아지고 있으며, 패스하는 분들은 관련it업계에서 많은 지식과 내공을 지닌 분들뿐입니다.
| Section | Weight | Objectives |
|---|---|---|
| Wired and Wireless Infrastructure | 30% | - Design for data, voice, video, location - Logical infrastructure requirements - Physical infrastructure requirements - Design high-density wireless networks - Design wireless bridging (mesh) - Design radio management |
| Mobility | 25% | - Design mobility groups - Optimize client roaming - Site Tags - Validate mobility tunneling |
| WLAN High Availability | 20% | - Design controller high availability - Design AP high availability |
| Wireless Site Survey | 25% | - Material attenuation and its design effects - Predictive site survey - Layer 1 site survey analysis - Post-deployment site survey - Planning tools and network metrics evaluation - Collect design requirements and evaluate constraints - Pre-deployment site survey |
ExamPassdump의 Cisco인증 300-110시험덤프자료는 여러분의 시간,돈 ,정력을 아껴드립니다. 몇개월을 거쳐 시험준비공부를 해야만 패스가능한 시험을ExamPassdump의 Cisco인증 300-110덤프는 며칠간에도 같은 시험패스 결과를 안겨드릴수 있습니다. Cisco인증 300-110시험을 통과하여 자격증을 취득하려면ExamPassdump의 Cisco인증 300-110덤프로 시험준비공부를 하세요.
질문 # 19
A conference center is designing a Wi-Fi 6 deployment for a room holding 2000 attendees, most of whom will use low-bandwidth applications. Which Wi-Fi 6 capability most directly improves efficiency in this scenario?
정답：D
설명：
The defining problem in a high-density room with many low-bandwidth clients is not raw per-client throughput but the overhead of medium contention - under 802.11ac, each small packet requires a full channel access cycle, so the channel spends most of its airtime on contention and preamble rather than payload. OFDMA divides the channel into resource units so the AP can serve multiple clients within a single transmit opportunity, dramatically reducing per-frame overhead when the traffic mix is many small transmissions. This is precisely the profile of a conference audience running chat, email, and browsing. 1024-QAM raises peak modulation but only benefits clients already at very high signal levels and does nothing for contention. 160 MHz channel bonding is counterproductive in high density because it collapses the number of reusable channels. Target Wake Time improves client battery life by scheduling wake intervals, which is valuable for IoT but does not address the airtime efficiency problem in this design.
질문 # 20
A consulting engineer for a copper mine is trying to extend the network connectivity of autonomous trucks via Cisco IW3702 APs. The WGB design requirements include: latency- sensitive application (truck slows at 10 sec, stops at 20 sec of connection loss), aggressive scanning and roaming, enterprise-grade security without certificates on each AP, multiple clients in different VLANs on the WGB, and channel scan parameters restricted to only channels in the truck path. Which design approach meets the requirements?
정답：C
설명：
This WGB (Workgroup Bridge) design scenario requires satisfying multiple simultaneous constraints. EAP-FAST (Flexible Authentication via Secure Tunneling) is the correct authentication protocol because it provides enterprise-grade 802.1X security using protected access credentials (PAC) without requiring a certificate to be installed on each AP or WGB device
-- directly satisfying the enterprise-grade security without certificates requirement. EAP-TLS (Options B and D) requires client certificates on every authenticating device, which is explicitly excluded. Mobile station mode is required rather than static mode (Options C and D) because mobile station mode enables the WGB to aggressively scan and roam to optimal mesh neighbors dynamically, evaluating neighbor signal quality and switching to better RAPs/MAPs as the truck moves along its path. Static mode fixes the WGB to a specific channel or AP, preventing the aggressive scanning and roaming required for the latency-sensitive application. The dot1q- capable switch connection supports multiple clients in different VLANs via 802.1Q VLAN tagging between the WGB and the truck's local network switch.
질문 # 21
A customer designs a Cisco wireless environment to provide connectivity to employees and guests. The guest SSID must be configured on three anchor WLCs named Anchor1, Anchor2, and Anchor3 in a DMZ. The guest anchor priority must be configured to ensure that Anchor1 has the highest priority. Which priority level must be incorporated in the design for Anchor1?
정답：D
설명：
In Cisco's guest anchor WLC deployment model, multiple anchor controllers can be configured in a DMZ to provide redundancy for guest WLAN traffic. The anchor priority value determines which anchor controller is preferred for establishing the guest mobility tunnel from the foreign WLC.
Cisco's anchor priority system assigns the highest preference to the lowest numerical priority value. Priority 1 is the highest priority, meaning the foreign WLC will prefer Anchor1 when establishing the CAPWAP mobility tunnel for anchoring guest client traffic. Priority 2 would be assigned to Anchor2, and Priority 3 to Anchor3, creating a deterministic failover hierarchy. If Anchor1 becomes unreachable, the foreign controller automatically falls over to Anchor2, then to Anchor3. Priority 0 is not a valid anchor priority value in the Cisco WLC configuration. This design pattern is critical for enterprise guest deployments where DMZ anchor redundancy must be maintained without manual intervention.
질문 # 22
During a client roaming event, which device is responsible for communicating the new Layer 2 EID mapping of a wireless supplicant to the fabric domain?
정답：D
설명：
During a client roaming event in a Cisco SD-Access fabric deployment, the Wireless LAN Controller (WLC) is responsible for communicating the new Layer 2 Endpoint ID (EID) mapping of a wireless supplicant to the fabric domain. In the SD-Access architecture, the WLC acts as a mobility orchestrator and serves as the interface between the wireless domain and the wired fabric. When a client roams from one AP to another, the WLC detects the roaming event and updates the fabric control plane with the new EID-to-RLOC (Routing Locator) mapping by notifying the fabric control plane node (CP). This ensures that the fabric knows the client ' s new location and can route traffic correctly without interruption. The Border Node (BN) handles traffic between the fabric and external networks. CP1 and CP2 are control plane nodes that maintain the mapping database but receive EID update notifications from the WLC - they do not initiate the EID mapping communication themselves. Reference: WLSD Study Guide - SD-Access Wireless Architecture, Client Roaming in Fabric Deployments, EID Mapping and Control Plane Notifications.
질문 # 23
A customer has a Cisco wireless network that supports VoWLAN services. The customer wants supported voice clients to receive roaming recommendations and suggestions from APs. This functionality must not impact non-VoWLAN clients. What should be enabled on the VoWLAN SSID?
정답：A
설명：
IEEE 802.11v BSS Transition Management is the standard that enables the network (via the AP) to actively provide roaming recommendations and suggestions to associated clients. When enabled on a SSID, the AP can send BSS Transition Management Request frames to clients, informing them of preferred target APs ranked by signal quality, load, and channel conditions.
Critically, BSS Transition Management is a voluntary mechanism -- clients that support 802.11v can act on the AP's recommendation, while clients that do not support 802.11v simply ignore the BSS Transition Request frames and continue operating normally. This selective applicability directly satisfies the requirement that non-VoWLAN clients must not be impacted.
질문 # 24
......
많은 분들은Cisco 300-110인증시험이 아주 어려운 것은 알고 있습니다. 하지만 우리ExamPassdump를 선택함으로Cisco 300-110인증시험은 그렇게 어렵지 않다는 것을 알게 될 것입니다. Pass4Tes의Cisco 300-110합습가이드는 시험의 예상문제부터 전면적이로 만들어진 아주 퍼펙트한 시험자료입니다. 우리의 서비스는Cisco 300-110구매 후 최신버전이 업데이트 시 최신문제와 답을 모두 무료로 제공합니다.
300-110시험대비 최신버전 문제: https://www.exampassdump.com/300-110_valid-braindumps.html