Fast2test為你提供了不同版本的資料以方便你的使用。PDF版的350-101考古題方便你的閱讀，為你真實地再現考試題目。軟體版本的350-101考古題作為一個測試引擎，可以幫助你隨時測試自己的準備情況。如果你想知道你是不是充分準備好了350-101考試，那麼你可以利用軟體版的考古題來測試一下自己的水準。這樣你就可以快速找出自己的弱點和不足，進而有利於你的下一步學習安排。
| Section | Objectives |
|---|---|
| Troubleshooting and Monitoring | - Wireless connectivity troubleshooting - Performance monitoring and diagnostics |
| Cisco Wireless Architecture | - Wireless LAN Controller (WLC) concepts - Lightweight Access Point (LAP) operation |
| Wireless Security | - WPA/WPA2/WPA3 security mechanisms - 802.1X and authentication methods |
| Mobility and Roaming | - Mobility groups and handoff mechanisms - Client roaming behavior |
| Wireless Fundamentals | - RF principles and radio frequency behavior - 802.11 standards overview - WLAN components and architecture basics |
| Wireless Deployment and Design | - Site survey and RF planning - Channel planning and interference mitigation |
Fast2test Cisco的350-101考試培訓資料是個性價很高的培訓資料，與眾多培訓資料相比，Fast2test Cisco的350-101考試培訓資料是最好的，如果你需要IT認證培訓資料，不選擇Fast2test Cisco的350-101考試培訓資料，你將後悔一輩子，選擇了Fast2test Cisco的350-101考試培訓資料，你將終身受益。
問題 #121
A school district is deploying Cisco Catalyst 9176 APs to remote sites with occasional WAN outages. The IT team wants the APs to attempt joining a secondary or tertiary Catalyst 9800 WLC if the primary controller is unreachable. The team must preconfigure all controller IP addresses using the AP CLI before deploying. Which set of CLI commands sets the primary, secondary, and tertiary controller IP addresses on a Catalyst 9176 AP?
答案：D
解題說明：
Cisco lightweight and Catalyst access points use CAPWAP for AP-to-controller discovery and join operations. For AP-side preconfiguration, Cisco documents the syntax as capwap ap {primary- base | secondary-base | tertiary-base} controller-name controller-ip-address, specifically for configuring primary, secondary, and tertiary controllers on the AP. This matches option B exactly because it includes the CAPWAP AP command, the controller priority keyword, the controller name, and the controller management IP address.
The Catalyst 9800 AP join process also recognizes these configured controller entries in priority order: primary controller using capwap ap primary-base, secondary controller using capwap ap secondary-base, and tertiary controller using capwap ap tertiary-base.
This allows the AP to attempt a backup controller when the preferred controller is unavailable, which is appropriate for remote sites with intermittent WAN reachability. Option A uses obsolete or invalid set controller syntax. Option C invents an ap join command format. Option D incorrectly inserts wlc into the AP CAPWAP command.
問題 #122 
Refer to the exhibit. An engineer is configuring a switch port for a Cisco Spaces deployment at a new branch site. The Spaces connector requires access to the management VLAN 30. The network team plans to add more analytics services in the future, so the configuration must also allow for easy scalability and avoid service interruption for currently connected devices and default switch VLAN settings. Which set of commands must be added to the box in the CLI to complete the configuration?
答案：D
解題說明：
The correct answer is D. Cisco Spaces connector deployments often require a VLAN on which the connector is reachable for management or data, and Cisco Spaces wired gateway guidance identifies the connector VLAN as the VLAN used for communication to the connector. The same guidance also supports multiple source VLANs for monitored wired devices, which aligns with the requirement for future analytics-service scalability.
A trunk port is the proper design choice because it can carry multiple VLANs over the same physical interface. Cisco Catalyst switch documentation states that an access port carries traffic for only one VLAN, while an IEEE 802.1Q trunk carries multiple VLANs and supports tagged traffic. The command switchport trunk allowed vlan 30 limits the trunk initially to VLAN 30, satisfying the current management VLAN requirement without changing the native VLAN or other default VLAN settings. Cisco also documents that an allowed VLAN list limits VLAN membership only on the associated trunk port, so it does not affect other switch ports.
Option A works only for a single untagged VLAN and is less scalable. Options B and C mix access mode with trunk-only commands and are syntactically or operationally invalid. Reference topic: Wireless Monitoring and Management - Cisco Spaces connector deployment, VLAN reachability, trunking, and analytics service scalability.
問題 #123
Refer to the exhibit. A wireless controller is deployed at a branch location to facilitate guest client connectivity. A network engineer configures one WLAN using Web authentication and activates web-based method to align with company security policies. Which configuration enables client authentication for this WLAN?
答案：B
解題說明：
The command that enables web-based client authentication on the WLAN is security web-auth.
Cisco's Catalyst 9800 Web-Based Authentication guide shows the WLAN configuration workflow:
enter WLAN configuration mode, disable WPA security for the open Layer 2 guest WLAN, then
"Enable web authentication for WLAN" using security web-auth. Cisco then applies the authentication list and parameter map with security web-auth authentication-list ... and security web-auth parameter-map ..., which refine the WebAuth method and portal behavior after WebAuth itself is enabled.
Cisco's LDAP authentication example mirrors the exhibit exactly: wlan webauth 2 webauth, removal of WPA/802.1X Layer 2 security, security web-auth, security web-auth authentication-list ldapauth, and security web-auth parameter-map global. Option B only creates or enters the WLAN profile with WLAN ID 2 and SSID name. Options C and D disable WPA2 and 802.1X AKM; they do not authenticate clients.
問題 #124
An engineer must troubleshoot complex wireless performance issues in a large office which is using a Cisco 9176 AP. The engineer must analyze traffic patterns and identify potential sources of interference. The AP must capture all wireless frames in the air and send them to a remote protocol analyzer for detailed inspection. Client connectivity is not required from the AP during the troubleshooting window. Which CLI command must the engineer use on the WLC to enable the required AP mode for this purpose?
答案：B
解題說明：
For in-depth wireless troubleshooting using a Cisco 9176 AP, the correct operational mode is the sniffer mode. This mode allows the AP to capture all RF frames, including management, control, and data frames, across all configured channels, and forward these to a remote protocol analyzer such as Wireshark. Sniffer mode is distinct from other AP modes because the AP does not serve clients in this state; its sole function is passive packet capture for analysis of interference, RF performance, and client behavior. The command ap name <ap_name> mode sniffer executed on the WLC explicitly sets this mode.
問題 #125 
Refer to the exhibit. An engineer is preparing a Cisco 9800-L WLC for deployment in a sensitive area. Only encrypted remote management via SSH is allowed, and all other VTY access methods must be disabled. The
9800-L WLC will be part of a larger deployment, and an external audit will check for any unencrypted management protocols. According to the requirements, only SSH is allowed for remote CLI sessions. Which set of commands must be executed to complete the Cisco IOS XE CLI configuration on the WLC?
答案：C
解題說明：
The correct configuration is option C because Cisco IOS XE restricts inbound protocols on VTY lines with thetransport inputcommand. Cisco's Catalyst 9800 best-practice guidance states that administrators should confirm SSH is enabled and Telnet is disabled for better controller security, and that the Catalyst 9800 follows standard Cisco IOS XE behavior for enabling or disabling Telnet and SSH. Cisco IOS XE SSH documentation explicitly showsline vty line_number [ending_line_number]followed bytransport input ssh, and explains that this prevents non-SSH Telnet connections, limiting access to SSH only.
The existing exhibit already includes the SSH prerequisites: hostname, domain name, RSA key generation, AAA new-model, a default login method using local credentials, and a local privileged user. The missing VTY configuration must therefore apply that default AAA login list to the VTY lines withlogin authentication defaultand restrict inbound transport to SSH. Cisco AAA documentation confirms thatlogin authentication defaultapplies the configured default authentication list to the line or set of lines. Option A is incomplete and does not explicitly permit SSH. Option B uses invalid syntax. Option D omits the requiredinputkeyword.
Reference topics:Catalyst 9800 secure management, VTY access control, SSH, Telnet hardening, AAA login authentication, and IOS XE device administration.
問題 #126
......
想參加Cisco的350-101認證考試嗎？你正在因為考試很難而發愁嗎？想報名參加考試，但是又擔心通過不了。你現在有這樣的心情嗎？沒關係，安心地報名吧。因為你只要用了Fast2test的資料，再難的考試也不是問題。即使你對通過考試一點信心也沒有，Fast2test的350-101考古題也可以保證你一次就輕鬆成功。覺得不可思議嗎？你可以來Fast2test的網站瞭解更多的資訊。另外，你還可以先試用350-101考古題的一部分。這樣的話你肯定就會知道，這個參考資料是你順利通過考試的保障。
350-101認證題庫: https://tw.fast2test.com/350-101-premium-file.html