今多くのIT技術会社は職員がInternational Code Councilの93-Tall-Mass-Timber-Buildings資格認定を持つのを要求します。International Code Councilの93-Tall-Mass-Timber-Buildings試験に合格するのは必要なことになります。速く試験に合格して資格認証を取得したいなら、我々MogiExamの93-Tall-Mass-Timber-Buildings問題集を使ってみてください。弊社はあなたに相応しくて品質高い93-Tall-Mass-Timber-Buildings問題集を提供します。また、あなたの持っている問題集は一年間の無料更新を得られています。あなたは十分の時間で93-Tall-Mass-Timber-Buildings試験を準備することができます。
| Section | Objectives |
|---|---|
| General & Construction Types | - Construction Classification — Type IV-A, IV-B, IV-C
|
| Fire-Resistance & Protection | - Noncombustible Protection & Encapsulation - Concealed Spaces Protection - Fire-Resistance-Rated Assemblies |
| Construction Fire Safety | |
| Mass Timber Materials | - CLT, Glulam, NLT, SCL and Engineered Wood Products |
| Structural & Connection Inspection | - Framing and Structural Elements - Connection Design and Protection |
| Inspection Duties & Documentation | - Statement of Special Inspections - Inspection Reporting and Compliance Verification |
>> 93-Tall-Mass-Timber-Buildingsサンプル問題集 <<
どんな業界で自分に良い昇進機会があると希望する職人がとても多いと思って、IT業界にも例外ではありません。ITの専門者はInternational Code Councilの93-Tall-Mass-Timber-Buildings認定試験があなたの願望を助けって実現できるのがよく分かります。MogiExamはあなたの夢に実現させるサイトでございます。
質問 # 49
Combustible construction forming concealed spaces shall be protected with noncombustible protection with an assigned time of 40 minutes in which construction type?
正解：B
解説：
The requirement applies to Type IV-C construction. Under the 2021 IBC provisions governing Type IV-C, combustible construction forming concealed spaces must be protected with noncombustible protection having an assigned protection time of not less than 40 minutes. Therefore, option C is correct.
The assigned protection time is determined using the protection-time values prescribed by the code, including the applicable values for gypsum board and other approved noncombustible materials. The provision is intended to delay ignition and involvement of combustible mass timber surfaces located within concealed spaces, where fire growth might otherwise remain undetected and become difficult for fire-suppression personnel to access.
Type IV-A and Type IV-B are subject to more extensive noncombustible protection requirements because those construction types support taller buildings and require greater protection of mass timber elements. Type IV-HT uses the traditional heavy-timber concealed-space provisions and may employ alternative methods, such as complete filling with noncombustible insulation.
During inspection, the special inspector must confirm that the installed layers, thicknesses, fastening patterns, joints, penetrations, and transitions collectively provide the required 40-minute assigned protection time.
References/Topics: 2021 IBC Section 602.4.3.5; Table 722.7.1(1); Type IV-C concealed-space protection.
質問 # 50
Calculated mass timber fire resistance can include each of the following except:
正解：A
解説：
Minimum prescriptive dimensions are not themselves a component added into a calculated fire-resistance time. Therefore, option A is the exception.
IBC Section 602.4 states that a mass timber element's required fire resistance can be based on the fire- resistance contribution of the mass timber, the noncombustible protection, or a combination of those two components. Options B, C, and D reflect those permitted approaches.
Minimum dimensions under Section 2304.11 serve a different function. They establish the minimum cross- sectional size and construction characteristics required for qualifying heavy timber or mass timber elements.
A member can satisfy the minimum dimensional requirement without automatically achieving every required one-, two-, or three-hour fire-resistance rating. The structural fire calculation must evaluate the remaining effective section after charring, elevated-temperature effects, applied loading, and any credited protective materials.
The inspector must therefore verify both requirements independently: the installed member must meet the minimum code dimensions and must match the approved fire-resistance design. Increasing a member to the minimum prescriptive size does not by itself replace the required calculation, tested assembly, or approved protection system.
References/Topics: 2021 IBC Sections 602.4, 703.2, 722.7 and 2304.11; calculated mass timber fire resistance.
質問 # 51
One code-recognized method for calculating the fire-resistance rating of exposed wood members and decking is:
正解：B
解説：
The intended answer is ANSI/AWC NDS Chapter 16. The video option uses "AWS," but the correct standards organization is the American Wood Council-AWC . Option D is therefore correct based on its intended reference.
IBC Section 722.1 expressly permits exposed wood members and wood decking to have their calculated fire resistance determined in accordance with Chapter 16 of the ANSI/AWC National Design Specification for Wood Construction. The method evaluates charring, the effective char depth, the reduced residual cross section, elevated-temperature effects, loading, and the remaining structural capacity for the required exposure period.
ACI 216.1 applies to concrete and masonry fire resistance. TMS 0216 addresses masonry assemblies. ASCE
29 Chapter 5 provides procedures for calculating the fire resistance of structural steel assemblies. Those references are code-recognized methods, but they apply to different construction materials.
For mass timber inspection, the approved calculations should identify the exposed surfaces, required rating, timber species or product, member dimensions, design loads, protective contribution, and connection treatment. Field reductions in member dimensions can invalidate the calculated fire resistance.
References/Topics: 2021 IBC Section 722.1; ANSI/AWC NDS Chapter 16; calculated fire resistance of exposed wood members and decking.
質問 # 52
What fire-resistance rating is required for floors in Type IV-A, IV-B and IV-C construction?
正解：D
解説：
IBC Table 601 requires floor construction and associated secondary structural members in Types IV-A, IV-B, and IV-C construction to have a two-hour fire-resistance rating. Therefore, option B is correct.
This requirement applies to the complete floor assembly, not only the timber panel. The required two-hour performance may be established through the calculated fire resistance of the mass timber, the contribution of approved noncombustible protection, or a permitted combination of both. Any topping, protective membrane, connection protection, and edge condition that forms part of the approved rated design must be installed accordingly.
The ratings for other building elements should not be transferred to the floor. A three-hour rating applies to the primary structural frame and bearing walls of Type IV-A, but its floor construction remains two hours.
Type IV-B and Type IV-C floors also require two hours, even though those construction types permit different degrees of exposed mass timber.
The special inspector must verify panel dimensions, approved layup, protection layers, joints, penetrations, connections, topping thickness, and other details that influence the floor's rated performance.
References/Topics: 2021 IBC Sections 601 and 602.4; Table 601, floor construction and associated secondary structural members.
質問 # 53
The fire-resistance of a protected mass timber assembly is equivalent to the fire resistance time of the:
正解：D
解説：
IBC Section 722.7 establishes the governing calculation principle for protected mass timber. The required fire resistance consists of the inherent fire resistance of the unprotected mass timber element plus the protection time contributed by the noncombustible protection . Therefore, option D is correct.
This approach recognizes two sequential protective mechanisms. First, the noncombustible covering delays heating and charring of the timber. After the credited protection period, the remaining mass timber cross section provides structural fire resistance through predictable charring behavior and residual section capacity.
Section 722.7.1 further requires the contribution of the covering material to comply with the prescribed protection times or to be established under Section 703.6.
Option A ignores the contribution of the protective membrane. Option B ignores the inherent structural fire resistance of the timber. Option C incorrectly substitutes a finish rating for the code-recognized protection contribution. A finish rating is a separate temperature-based performance concept and is not automatically additive as the protection time used by Section 722.7.
References/Topics: 2021 IBC Sections 602.4, 703.6, 722.7 and 722.7.1; calculation of protected mass timber fire resistance.
質問 # 54
......
International Code Councilさまざまな種類の候補者が93-Tall-Mass-Timber-Buildings認定を取得する方法を見つけるために、多くの研究が行われています。 シラバスの変更および理論と実践の最新の進展に応じて、93-Tall-Mass-Timber-Buildingsテストトレントを修正および更新します。 93-Tall-Mass-Timber-Buildings認定トレーニングは、厳密な分析による近年のテストと業界動向に基づいています。 したがって、お客様の93-Tall-Mass-Timber-Buildingsのために、より多くの選択肢が用意されています。試験のために93-Tall-Mass-Timber-Buildings試験問題を選択することをお勧めします。
93-Tall-Mass-Timber-Buildings出題内容: https://www.mogiexam.com/93-Tall-Mass-Timber-Buildings-exam.html