You can try our 300-110 study demo for free. There is no any personal information required from your side. The 300-110 complete study material contains comprehensive test information than the demo. So if you are interested with our 300-110 free demo then go for the 300-110 complete questions & answers. We will give you the best offer for the 300-110 practice dumps. 100% pass with 300-110 training dumps at first time is our guarantee.
| Section | Weight | Objectives |
|---|---|---|
| WLAN High Availability and Security Design | 20% | - High availability design
- Security architecture design
|
| Wireless Infrastructure Design | 30% | - Wired-wireless integration design
|
| Mobility Design | 25% | - Mobility architecture models
|
| Wireless Site Survey | 25% | - Design requirements collection and constraint evaluation
- RF propagation and attenuation analysis - Layer 1 site survey execution and analysis |
In this career advancement Designing Cisco Wireless Networks (300-110) certification journey you can get help from valid, updated, and real 300-110 Dumps questions which you can instantly download from ExamsLabs. At this platform, you will get the top-rated and Real 300-110 Exam Questions that are ideal study material for quick Cisco 300-110 exam preparation.
NEW QUESTION # 94
An engineer must assess an existing company WLAN to determine the possibility for future IEEE 802.11ac Wave 2 wireless deployment. All access switches are Fast Ethernet-capable only, and the wired infrastructure between existing APs and access switches is based on the CAT 6A standard. Which two actions provide maximum support of Cisco 3800 Series access points? (Choose two.)
Answer: B,D
Explanation:
Cisco 3800 Series APs support IEEE 802.11ac Wave 2, which can deliver throughput exceeding 1 Gbps. Fast Ethernet switches are limited to 100 Mbps per port, creating a severe bottleneck. The two actions that provide maximum support are replacing with mGig switches (Option A) and replacing with gigabit switches with 10G uplinks (Option B). mGig (Multi-Gigabit Ethernet) switches support 2.5G and 5G speeds over existing CAT
6A cabling, allowing the full throughput of 802.11ac Wave 2 APs to be utilized without replacing the existing cable plant. Gigabit switches with 10G uplinks ensure that the access layer can support 1 Gbps per AP port while providing sufficient uplink capacity. Since the existing cabling is already CAT 6A, which supports 10 Gbps over short distances and 5 Gbps over 100 meters, there is no need to replace the wiring (Option D eliminates). The 100-meter distance limitation (Option C) already applies to standard Ethernet and is met by CAT 6A - this is not an action but a constraint check. Option E (55 meters) is only relevant for specific
5GBASE-T configurations and doesn ' t maximize support compared to A and B. Reference: WLSD Study Guide - mGig Infrastructure, 802.11ac Wave 2 Infrastructure Design, Switch Upgrade Planning.
NEW QUESTION # 95
A wireless engineer is getting ready to perform a predictive site survey. The new network needs to support data and voice over wireless. Which two Cisco recommendations should be considered for the design?
(Choose two.)
Answer: C,D
Explanation:
For a network supporting both data and voice over wireless, two key Cisco design recommendations apply.
First, the 5 GHz radio band is recommended for voice over wireless due to its wider channel bandwidths, allowing for higher data rates and better quality of service for latency-sensitive applications. 40 MHz channels in the 5 GHz band provide significantly higher throughput than 20 MHz channels in 2.4 GHz, making Option B correct for the bandwidth reason stated. Second, setting the cell boundary to -67 dBm ensures sufficient signal strength for reliable voice communication at the cell edge, which is the Cisco standard threshold for VoWLAN coverage. Options C and E are partially correct (24 non-overlapping channels is accurate, 15-20% overlap is standard) but B and D are the primary Cisco recommendations that define the design targets for a predictive survey supporting voice. Reference: WLSD Study Guide - VoWLAN Design Requirements, Predictive Survey Design Criteria, 5 GHz Band Selection.
NEW QUESTION # 96
An engineer is designing a wireless network for a facility located 3 km from an airport with a terminal Doppler weather radar installation. Which design consideration applies to the 5 GHz channel plan?
Answer: B
Explanation:
Dynamic Frequency Selection is a regulatory requirement that obligates a Wi-Fi device operating on affected 5 GHz channels to detect radar signals and vacate the channel within a defined interval, then remain off that channel for a non-occupancy period of 30 minutes. When this occurs, the AP moves to a new channel and associated clients must re-associate, producing a brief but real service interruption. Near an airport with terminal Doppler weather radar, the probability of these events is materially higher, so the engineer must weigh the additional channel capacity DFS provides against the risk of periodic disruption - often excluding the channels closest to the radar's operating frequency for latency-sensitive SSIDs while retaining the rest.
DFS channels cannot be locked against radar-triggered changes, since compliance is mandatory.
DFS does not confer higher transmit power, and radar detection applies to UNII-2 and UNII-2 Extended, not UNII-1.
NEW QUESTION # 97
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?
Answer: C
Explanation:
The eping command is used on Cisco Wireless LAN Controllers to verify that the redundancy peer in a Stateful Switchover (SSO) pair of controllers is up and connected. This command sends ECHO packets (EoIP echo packets) to the peer controller to ensure the data path connectivity is functioning. In an SSO configuration, eping verifies the EoIP tunnel between the active and standby controllers, which is critical for state synchronization and seamless failover. If eping succeeds, it confirms that both the network path and the EoIP data encapsulation between the controllers are functional.
NEW QUESTION # 98
An engineer is implementing a wireless design for a manufacturing company with a Catalyst
9800, a stack of two Catalyst 9300-48HX switches, and 9166 APs. Each AP must be named using the Zone-053424189-01X string where X is the area number. The engineer needs to connect the APs to the switch stack using PoE. How many APs must the engineer connect to the stack so that they run with full functionality?
Answer: D
Explanation:
The Cisco Catalyst 9300-48HX is a high-density PoE switch specifically designed for Cisco Catalyst 9100 Series AP deployments. The 48HX variant features 48 Multi-Gigabit PoE ports with IEEE 802.3bt (PoE++) support, providing up to 90W per port. The Cisco 9166 Access Point is a Wi-Fi 6E AP that requires IEEE 802.3bt (PoE++) power to achieve full radio functionality -- enabling all three radios including the 6 GHz radio. In a two-switch stack of 48HX units, the total PoE budget is designed and rated to support full-port utilization with Cisco 9100 series APs simultaneously. The design intent is to connect APs to all ports on all switches -- maximizing the deployment density and ensuring every AP runs with full functionality. Connecting to only half the ports on one switch (Option B), half of each switch (Option C), or all ports on only one switch (Option D) would underutilize the infrastructure and fail to achieve the full deployment density that the switch stack was architected to deliver. The AP naming scheme requiring sequential area numbering requires all APs to be connected and fully operational across the entire stack.
NEW QUESTION # 99
......
It is believe that employers nowadays are more open to learn new knowledge, as they realize that Cisco certification may be conducive to them in refreshing their life, especially in their career arena. We attract customers by our fabulous 300-110 certification material and high pass rate, which are the most powerful evidence to show our strength. We are so proud to tell you that according to the statistics from our customersโ feedback, the pass rate among our customers who prepared for the exam with our 300-110 Test Guide have reached as high as 99%, which definitely ranks the top among our peers. Hence one can see that the Designing Cisco Wireless Networks learn tool compiled by our company are definitely the best choice for you.
300-110 Exam Questions Vce: https://www.examslabs.com/Cisco/CCNP-Wireless/best-300-110-exam-dumps.html