BTW, DOWNLOAD part of GetValidTest HPE7-A01 dumps from Cloud Storage: https://drive.google.com/open?id=19rPm9p-4j3jqYLcpx-vaWlvPgAZRHNF7
Up to now, we have business connection with tens of thousands of exam candidates who adore the quality of our HPE7-A01 exam questions. Besides, we try to keep our services brief, specific and courteous with reasonable prices of HPE7-A01 Study Guide. All your questions will be treated and answered fully and promptly. So as long as you contact us to ask for the questions on the HPE7-A01 learning guide, you will get the guidance immediately.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: Authentication & Authorization | 8% | - AAA Configuration
|
| Topic 2: Performance Optimization | 7% | - QoS and Optimization
|
| Topic 3: Network Fundamentals | 4% | - Network Stack
|
| Topic 4: Network Connectivity & Architecture | 8% | - Connectivity
|
| Topic 5: Security | 9% | - Network Security
|
| Topic 6: Routing | 13% | - Routing Implementation
|
| Topic 7: Monitoring & Management | 6% | - Network Monitoring Tools
|
| Topic 8: Switching & Layer 2/3 Technologies | 14% | - Campus Switching
|
| Topic 9: WLAN Technologies | 17% | - Wireless LAN Implementation
|
| Topic 10: Troubleshooting | 6% | - Wired and Wireless Troubleshooting
|
The authority of HP HPE7-A01 exam questions rests on its being high-quality and prepared according to the latest pattern. GetValidTest is proud to announce that our HP HPE7-A01 Exam Dumps help the desiring candidates of HP HPE7-A01 certification to climb the ladder of success by grabbing the HP Exam Questions.
NEW QUESTION # 155
Refer to Exhibit:
With Access-1, What needs to be identically configured With MSTP to load-balance VLANS?
Answer: A
Explanation:
The correct answer is B. Spanning-tree instance VLAN mapping.
To load-balance VLANs with MSTP, you need to configure the same VLAN-to-instance mapping on all switches in the same MST region. This means that you need to assign different VLANs to different MST instances, and then adjust the spanning tree parameters (such as priority, cost, or port role) for each instance to achieve the desired load balancing. For example, you can make one switch the root for instance 1 and another switch the root for instance 2, and then map half of the VLANs to instance 1 and the other half to instance 2.
According to the Cisco document Understand the Multiple Spanning Tree Protocol (802.1s), one of the steps to configure MST is:
* Split your set of VLANs into more instances and configure different MST settings for each of these instances. In order to easily achieve this, elect Bridge D1 to be the root for VLANs 501 through 1000, and Bridge D2 to be the root for VLANs 1 through 500. These statements are true for this configuration:
Switch D1(config)#spanning-tree mst configuration
Switch D1(config-mst)#instance 1 vlan 501-1000
Switch D1(config-mst)#exit
Switch D1(config)#spanning-tree mst 1 priority 0
Switch D2(config)#spanning-tree mst configuration
Switch D2(config-mst)#instance 2 vlan 1-500
Switch D2(config-mst)#exit
Switch D2(config)#spanning-tree mst 2 priority 0
The above commands create two MST instances, 1 and 2, and map VLANs 501-1000 to instance 1 and VLANs 1-500 to instance 2. Then, they make switch D1 the root for instance 1 and switch D2 the root for instance 2.
The other options are incorrect because:
* A. Spanning-tree bpdu-guard setting is a security feature that disables a port if it receives a BPDU from an unauthorized device. It does not affect load balancing with MSTP.
* C. Spanning-tree CIST mapping is not a valid command. CIST stands for Common and Internal Spanning Tree, which is the spanning tree instance that runs within an MST region and interacts with other regions or non-MST switches.
* D. Spanning-tree root-guard setting is another security feature that prevents a port from becoming a root port if it receives superior BPDUs from another switch. It does not affect load balancing with MSTP.
NEW QUESTION # 156
You are troubleshooting an issue with a pair of Aruba CX 8360 switches configured with VSX Each switch has multiple VRFs. You need to find the IP address of a particular client device with a known MAC address You run the "show arp" command on the primary switch in the pair but do not find a matching entry for the client MAC address.
The client device is connected to an Aruba CX 6100 switch by VSX LAG.
Which action can be used to find the IP address successfully?
Answer: B
Explanation:
The show arp command displays the ARP table for a specific VRF or all VRFs on the switch. The ARP table contains the IP address to MAC address mappings for hosts that are directly connected to the switch or reachable through a gateway. If the client device is connected to another switch by VSX LAG, the ARP entry for the client device will not be present on the primary switch unless it has communicated with it recently.
Therefore, to find the IP address of the client device, the administrator should run the show arp command on the secondary switch in the VSX pair, specifying the VRF name that contains the client device's subnet.
References: https://techhub.hpe.com/eginfolib/Aruba/OS-CX_10.04/5200-6692/GUID-9B8F6E8F-9C7A-4F0D-AE7B-9D8E6C5B6A7F.html
NEW QUESTION # 157
With the CX 6000 48G switch with uplinks of 1/1/47 and 1/1/48, what does the switch do when a client port detects a loop and tx-disable parameter is used?
Answer: A
NEW QUESTION # 158
Your Aruba CX 6300 VSF stack has OSPF adjacency over SVI 10 with LAG 1 to a neighboring device The following configuration was created on the switch:
Answer: B
Explanation:
OSPF (Open Shortest Path First) is a routing protocol that uses link-state information to calculate the best path to each destination in the network. OSPF establishes adjacencies with neighboring routers to exchange routing information and maintain a consistent view of the network topology1.
To establish an OSPF adjacency, the routers need to have some common parameters, such as the area ID, the network type, the hello interval, the dead interval, and the authentication method2. The routers also need to have a matching subnet mask on the interface that connects them3.
In this case, the Aruba CX 6300 VSF stack has an SVI (Switched Virtual Interface) on VLAN 10 with an IP address of 10.1.1.1/24 and a LAG (Link Aggregation Group) on port 1/1/1 and port 2/1/1 that connects to a neighboring device. The SVI is configured with OSPF area 0 and network type broadcast. The LAG is configured with OSPF passive mode, which means that it will not send or receive OSPF hello packets.
The neighboring device has an interface with an IP address of 10.1.1.2/24 and a LAG on port 1/0/1 and port 2/0/1 that connects to the Aruba CX 6300 VSF stack. The interface is configured with OSPF area 0 and network type broadcast.
Since the Aruba CX 6300 VSF stack and the neighboring device have the same area ID, network type, subnet mask, and default hello and dead intervals on their interfaces, they will be able to establish an OSPF adjacency over SVI 10 with LAG 1. The OSPF passive mode on the LAG will not affect the adjacency, because it only applies to the LAG interface, not the SVI interface.
NEW QUESTION # 159
Refer to Exhibit:
With Access-1, What needs to be identically configured With MSTP to load-balance VLANS?
Answer: A
Explanation:
The correct answer is B. Spanning-tree instance VLAN mapping.
To load-balance VLANs with MSTP, you need to configure the same VLAN-to-instance mapping on all switches in the same MST region. This means that you need to assign different VLANs to different MST instances, and then adjust the spanning tree parameters (such as priority, cost, or port role) for each instance to achieve the desired load balancing. For example, you can make one switch the root for instance 1 and another switch the root for instance 2, and then map half of the VLANs to instance 1 and the other half to instance 2.
According to the Cisco document Understand the Multiple Spanning Tree Protocol (802.1s), one of the steps to configure MST is:
Split your set of VLANs into more instances and configure different MST settings for each of these instances.
In order to easily achieve this, elect Bridge D1 to be the root for VLANs 501 through 1000, and Bridge D2 to be the root for VLANs 1 through 500. These statements are true for this configuration:
Switch D1(config)#spanning-tree mst configuration
Switch D1(config-mst)#instance 1 vlan 501-1000
Switch D1(config-mst)#exit
Switch D1(config)#spanning-tree mst 1 priority 0
Switch D2(config)#spanning-tree mst configuration
Switch D2(config-mst)#instance 2 vlan 1-500
Switch D2(config-mst)#exit
Switch D2(config)#spanning-tree mst 2 priority 0
The above commands create two MST instances, 1 and 2, and map VLANs 501-1000 to instance 1 and VLANs 1-500 to instance 2. Then, they make switch D1 the root for instance 1 and switch D2 the root for instance 2.
The other options are incorrect because:
A). Spanning-tree bpdu-guard setting is a security feature that disables a port if it receives a BPDU from an unauthorized device. It does not affect load balancing with MSTP.
C). Spanning-tree CIST mapping is not a valid command. CIST stands for Common and Internal Spanning Tree, which is the spanning tree instance that runs within an MST region and interacts with other regions or non-MST switches.
D). Spanning-tree root-guard setting is another security feature that prevents a port from becoming a root port if it receives superior BPDUs from another switch. It does not affect load balancing with MSTP.
NEW QUESTION # 160
......
You can find different kind of HP exam dumps and learning materials in our website. You just need to spend your spare time to practice the HPE7-A01 valid dumps and the test will be easy for you if you remember the key points of HPE7-A01 Test Questions and answers skillfully. Getting high passing score is just a piece of cake.
HPE7-A01 Valid Test Dumps: https://www.getvalidtest.com/HPE7-A01-exam.html
DOWNLOAD the newest GetValidTest HPE7-A01 PDF dumps from Cloud Storage for free: https://drive.google.com/open?id=19rPm9p-4j3jqYLcpx-vaWlvPgAZRHNF7