300-615최신덤프문제 - 300-615 Dump

Cisco인증300-615시험을 패스하기가 어렵다고 하면 합습가이드를 선택하여 간단히 통과하실 수 잇습니다. 우리Itcertkr에서는 무조건 여러분을 위하여 관연 자료덤프 즉 문제와 답을 만들어낼 것입니다. 우리덤프로Cisco인증300-615시험준비를 잘하시면 100%Cisco인증300-615시험을 패스할 수 있습니다. Itcertkr덤프로 여러분은Cisco인증300-615시험을 패스는 물론 여러분의 귀증한 간도 절약하실 수 있습니다.

시스코 300-615 시험에 합격하려면 데이터 센터 인프라 기술에 대한 깊은 이해와 그 지식을 실제 문제 해결 시나리오에 적용할 수 있는 능력이 필요합니다. 이 자격증을 취득하면 개인의 전문성이 인정되며 복잡한 데이터 센터 인프라 문제를 식별하고 해결할 수 있는 능력이 향상되며, 데이터 센터 운영 및 관리에서의 진출 기회를 제공할 수 있습니다.

>> 300-615최신덤프문제 <<

최신 CCNP Data Center 300-615 무료샘플문제 (Q203-Q208):

질문 # 203
Refer to the exhibit. The OSPF neighbor is stuck in the INIT state.
Which cause of this issue is true?

A. An ACL is blocking the hello packets.
B. An ACL is blocking unicast packets
C. The ID of the router is the same as the ID of the neighbor.
D. The MTU is misconfigured.

정답：A

설명：
https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/116422-technote-ospf-00.html#anc6

질문 # 204

Refer to the exhibit. The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?

A. IP address of the SNMP server
B. policy-default action statement
C. event statement
D. event-default action statement

정답：A

설명：
Section: Automation

질문 # 205

Refer to the exhibit. The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

A. switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val
50 poll-interval 1
switch(config-applet)# action 0.2 cli enable
switch(config-applet)# action 0.5 cli switchto vdc Core
switch(config-applet)# action 0.8 cli switchto vdc Distribution
B. switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-applet)# action 0.2 cli enable switch(config-applet)# action 0.5 cli switchto vdc Core switch(config-applet)# action 0.8 cli switchto vdc Distribution
C. switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val
50 poll-interval 1
switch(config-applet)# action 0.2 cli config t
switch(config-applet)# action 0.5 cli switchto vdc Core
switch(config-applet)# action 0.8 cli switchto vdc Distribution
D. switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-applet)# action 0.2 cli config t switch(config-applet)# action 0.5 cli switchto vdc Core switch(config-applet)# action 0.8 cli switchto vdc Distribution

정답：B

설명：
Section: Automation
Explanation/Reference: https://community.cisco.com/t5/networking-documents/eem-script-on-nexus-7000-switches-to- monitor-cpu-utilization/ta-p/3120112

질문 # 206
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

A. 1. Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2. Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3. Check for runtime link down status.
4. Reseat the affected IOM.
B. 1. Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2. Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3. Check for runtime link down status.
4. Reseat the affected IOM.
C. 1. Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2. Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3. Check for runtime link down status.
4. Reseat the affected IOM.
D. 1. Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2. Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3. Check for runtime link down status.
4. Reseat the affected IOM.

정답：A

설명：
Section: Compute Platforms
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/ UCSTroubleshooting_chapter_01001.html

질문 # 207
A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?

A. Clean reload the Leaf-1 switch
B. Define the new TEP address for Leaf-1
C. Change the clock offset from low to high between apic 1 and Leaf-1
D. Modify the ISIS interface peering IP address between apic 1 and Leaf-1

정답：B

질문 # 208
......

300-615 Dump: https://www.itcertkr.com/300-615_exam.html

300-615최신덤프문제 - 300-615 Dump

최신버전 300-615최신덤프문제 시험공부자료

최신 CCNP Data Center 300-615 무료샘플문제 (Q203-Q208):