P.S. Free & New 300-410 dumps are available on Google Drive shared by ActualCollection: https://drive.google.com/open?id=1vHB2K2IuCndDH41Ukf9PlghBP0faKQV9
With 300-410 training quiz, you only need to pay half the money to get the help of the most authoritative experts. 300-410 exam questions are also equipped with a mock examination function, that allowing you to find your own weaknesses at any time during the learning process of our 300-410 Study Materials, and to constantly improve your own learning methods. It also allows you to familiarize yourself with the examination environment in advance that helps you to avoid any emergency in the exam.
| Section | Weight | Objectives |
|---|---|---|
| VPN Services | 20% | - IPsec
|
| Infrastructure Security | 20% | - Device Security
|
| Infrastructure Services | 25% | - Network Performance Management
|
| Layer 3 Technologies | 35% | - Redistribute Routes
|
>> Cisco 300-410 Valid Exam Camp Pdf <<
Did you have bad purchase experience that after your payment your emails get no reply, your contacts with the site become useless? Stop pursuing cheap and low-price 300-410 test simulations. You get what you pay for. You may think that these electronic files don't have much cost. In fact, If you want to release valid & latest Cisco 300-410 test simulations, you need to get first-hand information, we spend a lot of money to maintain and development good relationship, we well-paid hire experienced education experts. We believe high quality of 300-410 test simulations is the basement of enterprise's survival.
NEW QUESTION # 118
Refer to the exhibit.
The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue?
Answer: C
Explanation:
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default. You can use the internal keyword along with the redistribute command under router bgp to redistribute OSPF intra- and inter-area routes.
Use the external keyword along with the redistribute command under router bgp to redistribute OSPF external routes into BGP.
-> In order to redistribute all OSPF routes into BGP, we must use both internal and external keywords. The full command would be (suppose we are using OSPF 1):
redistribute ospf 1 match internal external
Note: The configuration shows match internal external 1 external 2. This is normal because OSPF automatically appends "external 1 external 2" in the configuration. In other words, keyword external = external 1 external 2. External 1 = O E1 and External 2 = O E2.
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5242-bgp-ospf-redi s.html
NEW QUESTION # 119
Refer to the exhibit.
An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?
Answer: A
Explanation:
Explanation
From the output we notice that the destination IP address is not correct. The NMS server IP address should be 10.221.10.11, not 10.221.10.10. Therefore we have to change this information under "flow exporter ..." configuration.
NetFlow configuration reference: https://www.cisco.com/c/en/us/td/docs/iosxml/ ios/fnetflow/configuration/15-mt/fnf-15-mt-book/cfg-de-fnflow-exprts.html
NEW QUESTION # 120
LAB SIMULATION 1
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Do not replace existing routing policies or configurations.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Configure individual VRFs for each customer according to the topology to achieve these goals:
1. VRF "cu-red" has interfaces on routers R1 and R2. Both routers are preconfigured with IP addressing, VRFs, and BGP. Do not use the BGP network statement for advertisement.
2. VRF "cu-green" has interfaces on routers R1 and R2.
3. BGP on router R1 populates VRF routes between router R1 and R2.
4. BGP on router R2 populates VRF routes between router R1 and R2.
5. LAN to LAN is reachable between SW1 and SW3 for VRF "cu-red" and between SW2 and SW4 for VRF "cu-green". All switches are preconfigured.
Answer:
Explanation:
Use cu-red under interfaces facing SW1 & SW3:
On R1:
interface Ethernet0/0
ip vrf forwarding cu-red
ip address 192.168.1.254 255.255.255.0
Check reachability to SW1:
R1#ping vrf cu-red 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms On R2:
interface Ethernet0/0
ip vrf forwarding cu-red
ip address 192.168.2.254 255.255.255.0
Check reachability to SW3:
R2#ping vrf cu-red 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Use vrf cu-green for SW2 & SW4:
On R1:
interface Ethernet0/1
ip vrf forwarding cu-green
ip address 192.168.20.254 255.255.255.0
Test reachability to SW2:
R1#ping vrf cu-green 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
On R2:
interface Ethernet0/1
ip vrf forwarding cu-green
ip address 192.168.22.254 255.255.255.0
Test reachability to SW4:
R2#ping vrf cu-green 192.168.22.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
On R1:
interface Ethernet0/2.100
mpls ip
!
interface Ethernet0/2.200
mpls ip
!
Configure BGP:
router bgp 65000
neighbor 10.10.10.2 remote-as 65000
neighbor 10.10.20.2 remote-as 65000
!
address-family vpnv4
neighbor 10.10.10.2 activate
neighbor 10.10.20.2 activate
exit-address-family
!
address-family ipv4 vrf cu-green
redistribute connected
exit-address-family
!
address-family ipv4 vrf cu-red
redistribute connected
exit-address-family
!
R1(config)#ip vrf cu-red
R1(config-vrf)#route-target both 65000:100
!
R1(config)#ip vrf cu-green
R1(config-vrf)#route-target both 65000:200
On R2:
interface Ethernet0/2.100
mpls ip
!
interface Ethernet0/2.200
mpls ip
!
router bgp 65000
neighbor 10.10.10.1 remote-as 65000
neighbor 10.10.20.1 remote-as 65000
!
address-family vpnv4
neighbor 10.10.10.1 activate
neighbor 10.10.20.1 activate
exit-address-family
!
address-family ipv4 vrf cu-green
redistribute connected
exit-address-family
!
address-family ipv4 vrf cu-red
redistribute connected
exit-address-family
R2(config)#ip vrf cu-red
R2(config-vrf)#route-target both 65000:100
!
R2(config)#ip vrf cu-green
R2(config-vrf)#route-target both 65000:200
Verification:
From SW1 to SW3:
SW1#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
But can't Reach SW2 or SW4 in VRF cu-green:
SW1#ping 192.168.22.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
SW1#ping 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
Same Test for SW2:
From SW2 to SW4:
SW2#ping 192.168.20.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
But can't Reach SW3 or SW1 in VRF cu-red:
SW2#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
SW2#ping 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
Both R1 & R2 has separate tables for VRFs cu-red and cu-green.
NEW QUESTION # 121
Refer to the exhibit.
Users in VLAN46 cannot get the IP from the DHCP server. Assume that all the parameters are configured properly in VLAN 10 and on the DHCP server Which command on interlace VLAN46 allows users to receive IP from the DHCP server?
Answer: A
NEW QUESTION # 122
Refer to the exhibit.
The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?
Answer: A
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-withdefault- routes-using-I.html
NEW QUESTION # 123
......
Do you want to obtain the latest information for your exam timely? Then you can choose us, since we can do that for you. 300-410 study guide of us offers you free update for 365 days, so that you can get the latest information for the exam timely. And the latest version for 300-410 exam materials will be sent to your email automatically. In addition, 300-410 Exam Materials are compiled by experienced experts who are quite familiar with the exam center, therefore the quality can be guaranteed. We have online and offline service, and if you have any questions for 300-410 exam dumps, you can consult us.
300-410 Exam Quizzes: https://www.actualcollection.com/300-410-exam-questions.html
What's more, part of that ActualCollection 300-410 dumps now are free: https://drive.google.com/open?id=1vHB2K2IuCndDH41Ukf9PlghBP0faKQV9