The staffs of NSEI_OTS_AR-7.6 training materials are all professionally trained. If you have encountered some problems in using our products, you can always seek our help. Our staff will guide you professionally. If you are experiencing a technical problem on the system, the staff at NSEI_OTS_AR-7.6 practice guide will also perform one-on-one services for you. We want to eliminate all unnecessary problems for you, and you can learn our NSEI_OTS_AR-7.6 Exam Questions without any problems. You may have enjoyed many services, but the professionalism of NSEI_OTS_AR-7.6 simulating exam will conquer you.
| Section | Objectives |
|---|---|
| Network Access Control | - Explain OT Ethernet concepts - Configure network segmentation schemas - Configure network access authentication |
| Asset Management | - Implement device detection on FortiGate and FortiNAC - Use Fortinet Security Fabric for an OT network - Explain OT standards and Fortinet compliance |
| Network Security | - Configure virtual patching - Configure automation - Configure security inspections for industrial protocols |
| Monitoring and Risk Assessment | - Analyze security reports from FortiAnalyzer - Perform risk assessment and management - Create FortiAnalyzer event handlers |
>> Certification NSEI_OTS_AR-7.6 Test Questions <<
Do you want to pass your exam just one time? Then choose us, we can do that for you. NSEI_OTS_AR-7.6 exam cram contains both questions and answers, and you can have a quick check after practicing. NSEI_OTS_AR-7.6 exam materials are high-quality, because we have professional team to compile and verify them. In order to build up your confidence for NSEI_OTS_AR-7.6 Training Materials, we are pass guarantee and money back guarantee, and if you fail to pass the exam, we will give you fell refund. We provide you with free update for 365 days, so that you can know the latest information for the exam, and the update version for NSEI_OTS_AR-7.6 exam dumps will be sent to your email automatically.
NEW QUESTION # 29
Refer to the exhibits.
The Playbook Monitor dashboard and the analysis of the corresponding incident analysis are shown. You created the playbook with the objective of automatically attaching the report to the incident that was created.
Which two statements are correct? (Choose two answers)
Answer: C,D
Explanation:
The correct answers are C and D .
Option D is correct because the Playbook Monitor clearly shows the starter as On_Demand and the trigger as user(admin) . The study guide states that "ON_DEMAND: The playbook runs when an administrator manually starts it" and also notes that to run it manually, you select the playbook and click Run . This exactly matches the exhibit, so the playbook was manually triggered.
Option C is also correct. The study guide explains that "tasks run one after another" and that "if needed, the output of one task can be used by the tasks that follow it." It also gives an example where workflow logic matters, such as creating an incident and then attaching details to it. In the exhibit, the sequence shown is Attach_report , then Run_report , then Create_Incident , while the incident analysis shows no report attached . Since the report must exist and the incident must already be available before it can be attached properly, the task order is wrong and must be reordered.
Option B is incorrect because the monitor shows multiple tasks completed successfully, not only Create_Incident . Option A is not the best answer because the main problem demonstrated by the exhibits is not simply waiting time, but the incorrect workflow order. The playbook completed successfully, yet the report is still not attached, which indicates a design issue in the task sequence rather than just a delay.
NEW QUESTION # 30
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in firewall policy, which two statements are correct? (Choose two answers)
Answer: A,C
Explanation:
The correct answers are A and C . The study guide explains that "You can use application control signatures to detect OT protocols" and that application control provides "granular message type identification." In the exhibit, the Operational Technology application category is included in the Application Sensor profile, so OT application signatures are enabled in this profile.
Option C is also correct because the override table shows Modbus_Read.Holding.Registers = Allow and Modbus = Block . The study guide states that you can use specific granular application control signatures to allow a specific Modbus command and block all others , and it also shows that application control can identify read and write commands separately at message level. Therefore, Modbus write commands are blocked by this profile.
Option B is incorrect because the profile is not simply monitoring all OT protocols; it contains a Block action for Modbus. Option D is incorrect because the study guide links OT protocol visibility specifically to the monitor status , while in the exhibit Modbus_Read.Holding.Registers is set to Allow , not Monitor .
NEW QUESTION # 31
Refer to the exhibit.
Why is the OT View tab not available in the Asset Identity Center section of the FortiGate-1 device? (Choose one answer)
Answer: C
Explanation:
The correct answer is A . The study guide states that "The OT view is not available by default. You must enable it in the Feature Visibility section of the GUI or using the CLI command shown on this slide" and shows config system settings # set gui-ot enable . It also says that "After you enable the feature, the Asset Identity Center contains an Asset Identity List tab and an OT View tab." This directly explains why the OT View tab is missing: the feature that enables the Purdue-style OT display has not been enabled yet.
The OT View is the view that displays devices in a Purdue diagram , and the Asset Identity List also shows the current Purdue level for each device. Because the answer options do not explicitly say enable OT View in Feature Visibility , option A is the intended match, since it refers to enabling the Purdue-related OT display feature. Option B is incorrect because device detection affects visibility of devices, not whether the OT View tab exists. Option C is not supported by the study guide, and option D is also not given as the requirement for showing the OT View tab.
NEW QUESTION # 32
Refer to the exhibit.
A simplified OT network is shown. You want to optimize the protection of this OT network. Which two controls must you implement? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are B. IPS on FortiGate_Level5 and C. Virtual patching on FortiGate_Level2 .
The study guide explains that "the first line of defense is securing the IT side of your network" and that FortiGate should be placed to protect ICS environments and stop threats from propagating from IT into OT. It also states that IPS improves OT security because "today's threat landscape requires IPS to block a wider range of threats and improve OT security" and that in IPS mode, vulnerable devices are protected . This makes FortiGate_Level5 , at the upper boundary near the DMZ and external connectivity, the correct place to implement IPS as a primary protection control.
The study guide also states in the Purdue model section that "Level 2 consists of the processes and programs that control the PLCs, RTUs, and IEDs found at Level 1" and that "it is necessary to segment, or even microsegment, these servers with firewall segmentation, along with policies that include application control and virtual patching." In addition, the virtual patching section says "Virtual patching protects OT devices that have not yet been updated against vulnerability exploits" and applies when traffic related to the vulnerable device reaches the firewall policy. Since FortiGate_Level2 sits between the process network and the control network, it is the right enforcement point for virtual patching to protect the PLC-side assets.
Option A is not one of the best answers because offline IDS only detects and logs attacks; the guide says "no traffic flows through FortiGate" in offline IDS mode, whereas IPS can actually block threats. Option D is also not the best answer because OT signatures are enabled within the IPS framework, but the stronger control explicitly described for this design is to deploy IPS at the upper boundary and virtual patching closer to vulnerable OT devices .
NEW QUESTION # 33
Refer to the exhibits.
A partial Basic Event Handler page on FortiAnalyzer and the creation of a trigger in a FortiGate device are shown. To improve the protection of your OT network, you want to automate the handling of compromised devices notified through FortiAnalyzer. You have configured an event handler named Alert_trigger as shown in the exhibit. When you create the trigger on the FortiGate device, the Event handler name field does not provide the Alert_trigger option. What two actions must you perform to make the Alert_trigger option available? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are C and D .
Option C is correct because the study guide explains that when "a handler generates an event with the automation stitch option enabled, FortiAnalyzer sends a notification" and, in the Security Fabric workflow, "FortiAnalyzer parses the logs and notifies the root FortiGate." This means FortiGate must first have the FortiAnalyzer connection configured so it can consume FortiAnalyzer event handlers and use them in automation. The wizard message in the exhibit also points to this requirement by indicating that a FortiAnalyzer connection must be configured.
Option D is also correct because the study guide explicitly says that in this automation flow "the root FortiGate triggers the action" and shows "Stitches configured on root FortiGate." Therefore, if you want the FortiAnalyzer event handler to appear and be usable for automation, the trigger must be configured on the root FortiGate , not on an arbitrary downstream FortiGate.
Option A is incorrect because + Create is only a GUI control and does not solve the missing-event-handler visibility problem. Option B is not identified in the study guide as the requirement for making a FortiAnalyzer event handler available in the FortiGate automation trigger list.
NEW QUESTION # 34
......
The Fortinet NSEI_OTS_AR-7.6 certification will further demonstrate your expertise in your profession and remove any room for ambiguity on the hiring committee's part. People need to increase their level by getting the Fortinet NSEI_OTS_AR-7.6 Certification. You can choose flexible timings for the learning Fortinet NSEI_OTS_AR-7.6 exam questions online and practice with Fortinet NSEI_OTS_AR-7.6 exam dumps any time.
NSEI_OTS_AR-7.6 Valid Exam Camp Pdf: https://www.examdumpsvce.com/NSEI_OTS_AR-7.6-valid-exam-dumps.html