PassTIP NS0-185 최신 PDF 버전 시험 문제집을 무료로 Google Drive에서 다운로드하세요: https://drive.google.com/open?id=13kcRj6grlt1K3yjGASjBiqRaA-1n0c_D
우리PassTIP가 제공하는 최신, 최고의Network Appliance NS0-185시험관련 자료를 선택함으로 여러분은 이미 시험패스성공이라고 보실수 있습니다.
| Section | Objectives |
|---|---|
| Topic 1: ONTAP Networking | - Cluster networking configuration - Network types in ONTAP clusters |
| Topic 2: ONTAP Configuration | - Security hardening - Add or remove cluster nodes - Installation troubleshooting support tools - Cluster peering setup |
| Topic 3: Customer Handoff | - Customer delivery and handoff - Documentation creation - Installation validation tools |
| Topic 4: ONTAP Concepts | - Cluster controller components - Aggregate creation - Cluster installation and expansion - ONTAP updates and version management |
| Topic 5: Basic Installation Topics and Tools | - Physical cabling of ONTAP nodes - Installation preparation tools and documentation |
| Topic 6: ONTAP Switches | - Switched cluster cabling - Switch configuration software requirements |
PassTIP Network Appliance NS0-185덤프의 질문들과 답변들은 100%의 지식 요점과 적어도 98%의 시험 문제들을 커버하는,수년동안 가장 최근의Network Appliance NS0-185시험 요점들을 컨설팅 해 온 시니어 프로 IT 전문가들의 그룹에 의해 구축 됩니다. PassTIP의 IT전문가들이 자신만의 경험과 끊임없는 노력으로 최고의Network Appliance NS0-185학습자료를 작성해 여러분들이Network Appliance NS0-185시험에서 패스하도록 도와드립니다.
질문 # 78
After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA.
You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output.
In this scenario, what should you do next?
정답：B
설명：
This is a post-install validation and troubleshooting scenario for SAS shelf cabling. ONTAP hardware installation guidance distinguishes betweenmultipath/tri-pathandquad-pathconfigurations based on how shelves are cabled. For shelves with IOM12/IOM12B modules, quad-path configurations requiredouble-wide shelf-to-shelf connectivity: first using the standard connections (IOM ports 3 and 1) and then adding double- wide connections (IOM ports 4 and 2). If quad-path HA is intended but Config Advisor reportsmixed-path HA, then ONTAP's view of the end-to-end SAS topology does not match the expected double-wide design.
The question states LEDs look normal and rebooting the SAS expander did not change the status. That reduces the likelihood of a transient expander condition and shifts focus tophysical seating/connection integrity. In installation practice, a common next corrective step is tore-seat the SAS I/O modules(IOMs on the shelf side or SAS modules/adapters on the controller side depending on platform architecture). Reseating is a controlled, practical action to address partial lane connectivity, marginal contacts, or module insertion issues that can still present as "connected" at an LED level but result in ONTAP detecting fewer active paths than expected.
Option D is incorrect because multipath HA is not "the only" supported method on such platforms; ONTAP documentation explicitly describes quad-path ("double-wide") cabling rules and steps. Option B (disconnect and rerun Config Advisor) is destructive and does not correct the underlying condition; it is more of a diagnostic reset than a validated next fix step, and it risks creating additional variables. Option A (open a case and power off shelves) is premature given there is a clear, standard physical remediation action remaining.
Therefore, the correct next step is tore-seat the SAS IO modulesof the affected controller.
질문 # 79
You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither "un-failing" nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive. In this scenario, which two actions should you take? (Choose two.)
정답：B,D
설명：
Tech case required and run Config Advisor for analysis also log collection.
질문 # 80
You are assigned to install two DS2246 shelves, three DS4243 shelves, and one DS4486 shelf.
How many rack units (U space) should you account for in this rack layout?
정답：A
설명：
NetApp rack unit (U) sizing is defined per shelf model:
* DS2246 = 2U each # 2 × 2U = 4U
* DS4243 = 4U each # 3 × 4U = 12U
* DS4486 = 4U # 4U
Total:4U + 12U + 4U = 20U
Therefore, the correct answer is20U.
질문 # 81
You want to add an AFF A400 HA pair to an existing cluster.
In this scenario, which LIF type is required?
정답：D
설명：
When expanding an ONTAP cluster by adding new nodes or HA pairs,intercluster LIFsare required to enable secure communication between clusters or nodes during join and expansion workflows. Intercluster LIFs provide IP-based connectivity used for cluster peering, node addition, and replication setup.
Cluster management LIFs are used for administrative access, node management LIFs provide per-node management access, and data LIFs are used for client I/O. None of these LIF types support the inter-node communication required during cluster expansion.
Therefore, anintercluster LIFis required.
질문 # 82
You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.
Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)
정답：C,D
설명：
https://www.netapp.com/media/16885-tr-4182.pdf (Page 12)
질문 # 83
......
PassTIP는 오래된 IT인증시험덤프를 제공해드리는 전문적인 사이트입니다. PassTIP의 Network Appliance인증 NS0-185덤프는 업계에서 널리 알려진 최고품질의Network Appliance인증 NS0-185시험대비자료입니다. Network Appliance인증 NS0-185덤프는 최신 시험문제의 시험범위를 커버하고 최신 시험문제유형을 포함하고 있어 시험패스율이 거의 100%입니다. PassTIP의Network Appliance인증 NS0-185덤프를 구매하시면 밝은 미래가 보입니다.
NS0-185최신버전 덤프공부: https://www.passtip.net/NS0-185-pass-exam.html
참고: PassTIP에서 Google Drive로 공유하는 무료, 최신 NS0-185 시험 문제집이 있습니다: https://drive.google.com/open?id=13kcRj6grlt1K3yjGASjBiqRaA-1n0c_D