Our test engine is an exam simulation that makes our candidates feel the atmosphere of 300-110 actual test and face the difficulty of certification exam ahead. It reminds you of your mistakes when you practice 300-110 vce dumps next time and you can set your test time like in the formal test. Our 300-110 Training Materials cover the most content of the real exam and the accuracy of our 300-110 test answers is 100% guaranteed.
| Section | Weight | Objectives |
|---|---|---|
| Mobility | 25% | - Validate mobility tunneling - Site Tags - Design mobility groups - Optimize client roaming |
| WLAN High Availability | 20% | - Design AP high availability - Design controller high availability |
| Wired and Wireless Infrastructure | 30% | - Design for data, voice, video, location - Design radio management - Design high-density wireless networks - Physical infrastructure requirements - Logical infrastructure requirements - Design wireless bridging (mesh) |
| Wireless Site Survey | 25% | - Planning tools and network metrics evaluation - Predictive site survey - Pre-deployment site survey - Layer 1 site survey analysis - Post-deployment site survey - Collect design requirements and evaluate constraints - Material attenuation and its design effects |
The DumpsFree Cisco 300-110 PDF questions file, desktop practice test software, and web-based practice test software, all these three Cisco 300-110 practice test questions formats are ready for instant download. Just download any Cisco 300-110 Exam Questions format and start this journey with confidence. Best of luck with exams and your career!!!
NEW QUESTION # 53
A network engineer is designing a new wireless network. The network must include these requirements: ?optimized performance ?avoid interference ?availability in high-density areas ?roaming Which two approaches must be taken? (Choose two.)
Answer: A,D
Explanation:
The design requirements -- optimized performance, interference avoidance, high-density support, and roaming capability -- collectively point to a dual-band strategy using narrow channel widths.
For 5 GHz operation (Option A), 20 MHz channels are the correct choice for high-density and campus- scale deployments. The 5 GHz band has significantly more non-overlapping channels compared to 2.4 GHz (up to 24 non-overlapping 20 MHz channels in UNII-1, UNII-2, and UNII-3), enabling a robust channel reuse plan with minimal co-channel interference and excellent roaming cell separation.
NEW QUESTION # 54
A university wants to deploy a high density of APs in an area where a high number of users congregate. Which functionality allows the university to optimize the RF settings for APs that operate in different environments or coverage zones?
Answer: B
Explanation:
RF Profiles are a Cisco WLC configuration construct that allows administrators to define a customized set of Radio Resource Management (RRM) parameters and apply them to a subset of APs operating in a specific environment or coverage zone. Within a university high-density deployment -- where a lecture hall, outdoor quad, cafeteria, and library may each require fundamentally different RF settings -- RF Profiles enable differentiation without globally modifying all RRM parameters. An RF Profile can define custom values for: minimum mandatory data rates, maximum transmit power, minimum transmit power, channel width (20/40/80 MHz), RxSOP thresholds, client load balancing parameters, and coverage hole detection sensitivity. This allows the engineer to apply aggressive interference mitigation settings to high-density assembly areas while maintaining full-coverage settings for perimeter zones.
NEW QUESTION # 55
A customer has an existing wireless network with a Cisco 9800 WLC high availability cluster and Cisco 9120 APs. The customer asks an engineer to perform a post wireless survey that includes a list of any non-802.11 devices on the 5 GHz band. The engineer performs the survey using an
802.11a/b/g/n/ac/ax WLAN adapter but did not use a spectrum analyzer. Which approach meets the requirements?
Answer: D
Explanation:
Non-802.11 device detection on the 5 GHz band without a dedicated spectrum analyzer is possible through Cisco's CleanAir technology, which is embedded as an RF ASIC in many Cisco AP models including the 9120 series. CleanAir operates at the hardware layer -- below the
802.11 MAC -- enabling the APs to detect, classify, and report non-802.11 interference sources such as cordless phones, microwave ovens, video cameras, radar, and other unlicensed RF emitters in the 5 GHz spectrum. The WLC aggregates CleanAir reports from all APs and provides a consolidated interference device list accessible through the WLC's monitoring interface. Since the question specifies the 5 GHz band, the relevant 802.11 protocol for 5 GHz is 802.11a (and its successors 802.11n and 802.11ac). Exporting the list of 802.11a interferers from the WLC using the CleanAir RF ASIC correctly targets the 5 GHz band and identifies non-802.11 devices detected there.
NEW QUESTION # 56
An engineer must perform a predictive design for a wireless network.
The customer has devices that can tolerate at most 100 ms of delay when roaming. Which design criteria must be used?
Answer: A
Explanation:
Devices that can tolerate at most 100 ms of delay when roaming are voice devices. The 100 ms maximum roaming delay threshold is the Cisco-specified design criterion for VoWLAN implementations -- it defines the maximum time a handset can tolerate being disconnected from the wireless network during a roam event before the voice call is degraded or dropped. This threshold drives specific design requirements: 15-20% cell overlap at -67 dBm, fast roaming mechanisms (802.11r, CCKM, or OKC), and AP placement along user movement paths.
NEW QUESTION # 57
A hospital has a Cisco Catalyst 9800 Series Wireless Controller in an SSO solution deployed in the primary data center. The hospital plans to increase redundancy in the wireless environment.
Management decides to deploy an extra Catalyst 9800 WLC offsite to another data center on a different subnet. A WAN link connects the data centers with a firewall at both ends. Which two design approaches must the engineer take to ensure that the APs can fail over? (Choose two.)
Answer: A,B
Explanation:
For APs to be able to fail over between a primary SSO pair in one data center and a standalone WLC in a remote data center connected via WAN with firewalls, two design requirements must be met. First, a mobility tunnel must be created between the wireless controllers (Option A). The mobility tunnel enables the controllers to exchange mobility control messages, peer information, and eventually AP context when failover occurs. Without the mobility tunnel, the remote WLC is not recognized as a valid failover target by the APs through the mobility domain. Second, UDP ports 16666 and 16667 must be open through the firewalls between the controllers (Option D).
UDP port 16666 is used for mobility control traffic and UDP port 16667 is used for mobility data traffic -- both must be permitted through the firewalls at both data centers for the mobility tunnel to establish and function.
NEW QUESTION # 58
......
As long as you need the exam, we can update the Cisco certification 300-110 exam training materials to meet your examination needs. DumpsFree's training materials contain many practice questions and answers about Cisco 300-110 and they can 100% ensure you pass Cisco 300-110 exam. With the training materials we provide, you can take a better preparation for the exam. And we will also provide you a year free update service.
Reasonable 300-110 Exam Price: https://www.dumpsfree.com/300-110-valid-exam.html