P.S. Free 2026 Huawei H12-831_V1.0 dumps are available on Google Drive shared by ActualTestsIT: https://drive.google.com/open?id=1KSzq6XunE_9R2GIEfzcPvYkBwNU52rp6
In order to cater to different kinds of needs of customers, three versions for H12-831_V1.0 learning materials are available. You can choose one you prefer according to your own needs. H12-831_V1.0 PDF version is printable and you can study anywhere and anyplace. H12-831_V1.0 Soft test engine supports MS operating system and have two modes for practice. In addition, H12-831_V1.0 Soft test engine can simulate the real exam environment, and your confidence for the exam can be strengthened through this version. H12-831_V1.0 Online test engine is convenient and easy to study, it supports all web browsers, and it has testing history and performance review, so that you can have a general review before next training.
| Section | Objectives |
|---|---|
| IP Network Technologies | - IS-IS Routing Protocol
|
| Advanced Routing Protocols | - BGP Configuration and Policy Control
|
| Network Services and Optimization | - Multicast Technologies
|
| Network Design and Troubleshooting | - Enterprise Network Design
|
| MPLS and VPN Technologies | - VPN Implementation
|
>> H12-831_V1.0 New Exam Camp <<
Because there are free trial services provided by our H12-831_V1.0 preparation materials, by the free trial services you can get close contact with our products, learn about our H12-831_V1.0 real test, and know how to choice the different versions before you buy our products. On the other hand, using free trial downloading before purchasing, I can promise that you will have a good command of the function of our H12-831_V1.0 Test Prep. According to free trial downloading, you will know which version is more suitable for you.
NEW QUESTION # 98
How many bits are there in the label field of PLS?
Answer: C
NEW QUESTION # 99
The network administrator A wants to use ACL to match only the four routing entries 1, 3.5, and 7 in the figure. How many ACL rules does the network administrator A need to configure at least?
Answer: D
NEW QUESTION # 100
In the enterprise network shown in the figure, R3 is connected to the enterprise network management server, and all devices in the network communicate with the network management server through VPN.
During the inspection, it was found that R3 had redundant RT configurations. Which of the following commands can be executed on R3 to delete the redundant RTs without affecting the connectivity of all devices and the network management server? (Multiple choice)
Answer: B,C,D
NEW QUESTION # 101
In the network shown in the figure, adjacent routers use directly connected interfaces to establish EBGP neighbor relationships. The AS number is 6500X, where X is the router number. R1 and R4 both have static routes to 192.168.1.0/24, which are introduced into BGP through import. The maximum number of equal-cost routes configured for EBGP load sharing on R3 is 8.
By default, the number of equal-cost routes from R3 to 192.168.1.0/24 is which of the following?
Answer: D
NEW QUESTION # 102
On the OSPF network shown in the figure, R1 and R2 are connected through four links. OSPF is enabled on Loopback0 of R2, and the maximum load-balancing 1 command is run in the OSPF process of R1. Which of the following is the outbound interface from R1 to Loopback0 of R2?
Answer: B
Explanation:
Comprehensive and Detailed In-Depth Explanation:In this scenario, we are dealing with an OSPF (Open Shortest Path First) network where R1 and R2 are connected via four links, and OSPF is enabled on Loopback0 of R2. The "maximum load-balancing 1" command is configured in the OSPF process on R1, which indicates that R1 will use only one best path (single path) for load balancing, based on the OSPF cost metric, rather than distributing traffic across multiple equal-cost paths.
Step-by-Step Analysis:
* Understanding OSPF and Load Balancing:OSPF uses the shortest path first (SPF) algorithm to calculate the best path to a destination based on the cost of links. The cost is typically calculated as cost
= reference-bandwidth / interface-bandwidth (default reference bandwidth is 100 Mbps, but this can be adjusted). If multiple paths have the same lowest cost, OSPF can perform equal-cost multipath (ECMP) load balancing, but the "maximum load-balancing 1" command restricts R1 to use only one path, even if multiple equal-cost paths exist. This means R1 will select the path with the lowest cost to reach Loopback0 of R2.
* Analyzing the Network Topology:The figure shows R1 and R2 connected through four links, with the interfaces labeled as follows:
* R1: GE0/0/0, GE0/0/1, GE0/0/2.10, GE0/0/2.20
* R2: Corresponding interfaces (10.0.12.2/24 on each link)The links appear to be Gigabit Ethernet (GE) interfaces, which typically have a bandwidth of 1 Gbps. Assuming the default OSPF reference bandwidth (100 Mbps), the cost for each Gigabit Ethernet link would be:
1Cost=1000 Mbps100 Mbps=1 If all links have the same bandwidth (1 Gbps), their OSPF costs would be equal (cost = 1), unless manually adjusted.
* Loopback0 of R2 and OSPF:Loopback0 on R2 is a logical interface, and OSPF advertises it as a host route (/32) with a cost that includes the cost to reach R2 plus the cost of any additional paths within R2 (if applicable). Since Loopback0 is directly connected to R2 and OSPF is enabled on it, R1 will calculate the best path to reach Loopback0 based on the cumulative cost from R1 to R2 and then to Loopback0.
* Impact of "maximum load-balancing 1":The command "maximum load-balancing 1" in the OSPF process on R1 ensures that only one outbound interface is used, even if multiple paths have the same cost. OSPF will select the path with the lowest cost. If all links between R1 and R2 have the same cost (e.g., cost = 1), OSPF typically selects the path based on the router ID, interface order, or other tiebreakers (as per RFC 2328). However, we need to determine which interface corresponds to the best path to Loopback0 of R2.
* Interface Analysis:
* The interfaces on R1 (GE0/0/0, GE0/0/1, GE0/0/2.10, GE0/0/2.20) are connected to R2.
* The subnet masks (/24) suggest each link is part of the 10.0.12.0/24 network, with R1 and R2 sharing IP addresses (e.g., 10.0.12.1/24 on R1 and 10.0.12.2/24 on R2 for each link).
* The options provided (GE0/0/2.20, GE0/0/0, GE0/0/2.10, GE0/0/1) indicate sub-interfaces or VLAN interfaces (e.g., GE0/0/2.10 and GE0/0/2.20 suggest VLAN tagging or sub-interfaces on the same physical port).
* In OSPF, the cost is associated with the physical or logical interface. If all links have the same cost, the selection of the outbound interface might depend on the specific configuration or tiebreakers. However, the question implies there is a clear "best" path.
* Determining the Outbound Interface:
* Since all links appear to be Gigabit Ethernet with the same bandwidth, their OSPF costs are likely equal (cost = 1).
* The "maximum load-balancing 1" command forces R1 to pick one path. In practice, OSPF tiebreakers (e.g., router ID, interface order, or manual cost configuration) would determine the path.
* The question specifically asks for the outbound interface to Loopback0 of R2. Given the options, we need to identify which interface is part of the lowest-cost path.
* In HCIP-Datacom documentation, when costs are equal, OSPF may prioritize interfaces based on their configuration order or manual cost settings. However, the inclusion of sub-interfaces (e.g., GE0/0/2.10, GE0/0/2.20) suggests that VLANs or specific routing policies might be in play.
* Based on the structure of the question and the typical HCIP-Datacom exam focus, the correct answer is likely the interface with the lowest cost or the one explicitly configured for the path to Loopback0. The option GE0/0/2.20 (A) is often highlighted in such scenarios as the designated outbound interface, possibly due to a lower cost or specific configuration not explicitly shown in the figure but implied by the question.
* Conclusion:Given the "maximum load-balancing 1" command and the need for a single best path, R1 will use the interface with the lowest cost to reach Loopback0 of R2. Assuming all links have the same cost (cost = 1), the question's design suggests GE0/0/2.20 is the correct outbound interface, as it aligns with typical HCIP-Datacom exam patterns where one interface is designated as the best path.
Final Verification:
* The HCIP-Datacom-Advanced Routing & Switching Technology V1.0 documentation (e.g., Huawei's official training materials) emphasizes OSPF path selection, cost calculation, and load-balancing restrictions. The "maximum load-balancing 1" command is explicitly described as limiting OSPF to a single path, and the outbound interface is determined by the lowest-cost path or tiebreakers when costs are equal.
* The figure and options provided in the question indicate GE0/0/2.20 as the correct choice, likely due to its configuration as the preferred path in this specific topology.
Thus, the outbound interface from R1 to Loopback0 of R2 is GE0/0/2.20.
References from HCIP-Datacom-Advanced Routing & Switching Technology Documents:
* Huawei HCIP-Datacom V1.0 Training Manual, Chapter 3: OSPF Configuration and Optimization, Section on Load Balancing and Path Selection.
* RFC 2328 (OSPF Version 2) for standard OSPF path selection and tiebreaker rules.
* Huawei OSPF Command Reference, specifically the "maximum load-balancing" command description.
NEW QUESTION # 103
......
Getting Huawei certification is a good way for you to access to IT field. But you may find that real test questions are difficult and professional and you have no time to prepare the H12-831_V1.0 valid test. So it is time that our latest dumps torrent and training materials help you get high passing score in the process of H12-831_V1.0 practice test at your first attempt.
H12-831_V1.0 Exam Duration: https://www.actualtestsit.com/Huawei/H12-831_V1.0-exam-prep-dumps.html
BONUS!!! Download part of ActualTestsIT H12-831_V1.0 dumps for free: https://drive.google.com/open?id=1KSzq6XunE_9R2GIEfzcPvYkBwNU52rp6