The Dumpleader is one of the leading brands that have been helping Fortinet NSEI_OTS_AR-7.6 Certification aspirants for many years. Hundreds of Fortinet Fortinet NSE I - OT Security 7.6 Architect exam applicants have achieved the Fortinet NSE I - OT Security 7.6 Architect in Procurement and Supply Fortinet certification. All these successful Fortinet test candidates have prepared with real and updated Fortinet NSE I - OT Security 7.6 Architect in Procurement and Supply Fortinet Questions of Dumpleader. If you also want to become Fortinet NSE I - OT Security 7.6 Architect in Procurement and Supply Fortinet certified, you should also prepare with our Fortinet Fortinet NSE I - OT Security 7.6 Architect actual exam questions.
| Section | Objectives |
|---|---|
| Network Access Control | - Configure network segmentation schemas - Configure network access authentication - Explain OT Ethernet concepts |
| Asset Management | - Explain OT standards and Fortinet compliance - Implement device detection on FortiGate and FortiNAC - Use Fortinet Security Fabric for an OT network |
| Monitoring and Risk Assessment | - Perform risk assessment and management - Create FortiAnalyzer event handlers - Analyze security reports from FortiAnalyzer |
| Network Security | - Configure virtual patching - Configure security inspections for industrial protocols - Configure automation |
>> NSEI_OTS_AR-7.6 Valid Real Test <<
All these three Fortinet NSEI_OTS_AR-7.6 exam questions formats are easy to use and compatible with all devices, operating systems, and browsers. You can install and run these three NSEI_OTS_AR-7.6 exam practice test questions easily and start Fortinet NSEI_OTS_AR-7.6 Exam Preparation without wasting further time. The NSEI_OTS_AR-7.6 exam practice questions will ace your Fortinet NSE I - OT Security 7.6 Architect NSEI_OTS_AR-7.6 exam preparation and prepare you for the final NSEI_OTS_AR-7.6 exam.
NEW QUESTION # 13
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: A
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 14
Refer to the exhibit.
A partial OT network is shown.
You have recently removed the air gap in the network to provide full connectivity.
What must you configure to protect your OT network from external attacks?
Answer: A
Explanation:
The correct answer is D . Removing the air gap creates connectivity between the OT environment and external networks, significantly increasing exposure to unauthorized access and cyberattacks. Fortinet explains that the expansion of remote connectivity and IT/OT interconnections increases the OT attack surface and that the modern threat landscape requires IPS to block a wider range of threats . In the shown Purdue-style topology, FortiGate_Level5 is positioned at the upper boundary toward external connectivity and is therefore the appropriate enforcement point for protecting against attacks entering from outside the OT environment. Virtual patching at Level 2 is intended primarily to compensate for known vulnerabilities on specific OT devices that cannot yet be patched. Application Control provides industrial protocol visibility and command-level control, while merely enabling OT signatures at Level 3 does not replace perimeter intrusion prevention. Consequently, IPS belongs on FortiGate_Level5 .
NEW QUESTION # 15
Refer to the exhibit.
A Run_report task is shown. You want to automate the generation of a newly created report on FortiAnalyzer . When you configure the Run_report task in Playbook, why is the report not shown in the Report field? (Choose two answers)
Answer: B,D
Explanation:
Based on the architecture of FortiAnalyzer within the Security Fabric and its automation capabilities:
* Automation Stitch and Reports : Within the Security Fabric environment, FortiAnalyzer serves as a key element in creating automation stitches and playbooks. For a report to be selectable within a Playbook task (such as the Run_report task shown in the exhibit), it must meet specific technical prerequisites in the report configuration.
* Auto-cache Requirement (Answer C) : For a report to be used for automated generation, it must be " ready " to be processed by the engine without manual intervention. Auto-cache must be enabled in the report settings to ensure the report can be generated dynamically and efficiently when triggered by the playbook.
* Extended Log Filtering (Answer B) : Playbooks often pass specific variables from the trigger (such as a specific device IP or a time range) into the report. For the report to accept these dynamic parameters and be visible as an " automation-compatible " report in the Playbook interface, Extended Log Filtering must be enabled.
* Workflow Constraints : Without these two settings enabled on the report itself, the Playbook engine cannot guarantee the report ' s successful generation or parameter injection, and thus filters it out of the available selection list in the Run_report task.
NEW QUESTION # 16
Refer to the exhibit.
A FortiAnalyzer report is shown.
You must extract relevant information provided by the report regarding your OT network.
Which two statements are correct? (Choose two.)
Answer: A,B
Explanation:
The correct answers are B and C . The exhibit ' s Top Threat section identifies the IPS threats as Blocked , directly confirming that the attacks were prevented rather than merely detected. The OT Traffic table also shows destination port 502 . Modbus/TCP conventionally operates on TCP port 502, and the OT Security 7.6 study guide identifies Modbus as an industrial protocol supported and inspected by Fortinet OT security controls. The report does not cover only one day; its displayed timeline spans multiple dates, from approximately October 30 through November 3. Option D is also inconsistent with the report because the visible OT destination addresses are associated with the 192.168.x.x networks rather than 10.1.5.1.
FortiAnalyzer reports summarize logged information into charts and tables specifically to expose traffic patterns, threats, and OT activity such as this.
NEW QUESTION # 17
Refer to the exhibit.
Which statement about this partial Asset Identity List page is correct? (Choose one answer)
Answer: C
Explanation:
The correct answer is B. A firewall policy has a Virtual Patching security profile applied to it .
The decisive clue in the exhibit is the Vulnerabilities column showing KEVs and device-specific vulnerability counts. The study guide explains the virtual patching workflow in this exact way: "FortiGate performs a lookup for device-specific vulnerabilities and mitigation rules in FortiGuard," then
"FortiGuard returns specific OT virtual patching signatures," and "FortiGate caches the signatures and mitigation rules that apply to each device." That is the same behavior reflected by the Asset Identity List showing vulnerability information per detected device.
The guide then states that "When traffic related to the vulnerable device reaches FortiGate, the firewall policy with the virtual patching profile applies." It also says "A virtual patching profile can be applied to firewall policies in any direction, protecting traffic from or to the vulnerable OT device." This directly links the per-device vulnerability visibility to a Virtual Patching profile enforced through firewall policy.
The other options do not match the exhibit. Antivirus is not described in the study guide as building a device- by-device vulnerability list, Application Control is used for OT protocol and message visibility, and IPS focuses on exploit detection and prevention. The Vulnerabilities/KEVs display is the indicator that FortiGate is using Virtual Patching logic for those OT devices.
NEW QUESTION # 18
......
If you are worried about your NSEI_OTS_AR-7.6 real exam and you are not prepared so, now you don't need to take any stress about it. Get most updated Fortinet dumps torrent with 100% accurate answers. Our website is considered one of the best website where you can save extra money by getting one-year of free updates after buying the NSEI_OTS_AR-7.6 Dumps PDF files.
NSEI_OTS_AR-7.6 Valid Test Online: https://www.dumpleader.com/NSEI_OTS_AR-7.6_exam.html