BONUS!!! Download part of Prep4sureExam NSEI_OTS_AR-7.6 dumps for free: https://drive.google.com/open?id=18b-YBBHAWlnpgqRZZhMWWbYihRy_Y5O2
We offer you free update for one year if you buy NSEI_OTS_AR-7.6 training materials from us. That is to say, in the following year, you will get the latest version once the NSEI_OTS_AR-7.6 exam dumps update. It can save your money for buying new version. In addition, the NSEI_OTS_AR-7.6 learning materials of us is compiled by experienced experts, and the quality can be guaranteed, you can pass your exam just one time by using ourNSEI_OTS_AR-7.6 Exam Dumps. We also have online and offline service stuff, if you have any question, you can consult us.
| Section | Objectives |
|---|---|
| Topic 1: Monitoring and risk assessment | - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers - Perform risk assessment and management |
| Topic 2: Network access control | - Configure network segmentation schemas - Explain OT Ethernet concepts - Configure network access authentication |
| Topic 3: Network security | - Configure security inspections for industrial protocols - Configure automation - Configure virtual patching |
| Topic 4: Asset management | - Implement device detection on FortiGate and FortiNAC - Fortinet Security Fabric for an OT network - Explain OT standard and Fortinet compliance |
>> Certification NSEI_OTS_AR-7.6 Torrent <<
Our NSEI_OTS_AR-7.6 training materials have been honored as the panacea for the candidates for the exam since all of the contents in the NSEI_OTS_AR-7.6 guide materials are the essences of the exam. There are detailed explanations for some difficult questions in our NSEI_OTS_AR-7.6 exam practice. Consequently, with the help of our study materials, you can be confident that you will pass the exam and get the related certification as easy as rolling off a log. So what are you waiting for? Just take immediate action to buy our NSEI_OTS_AR-7.6 learning guide!
NEW QUESTION # 36
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in a firewall policy, which two statements are correct? (Choose two answers)
Answer: B,D
Explanation:
The correct answers are A and C .
Option C is correct because the profile clearly contains the Operational Technology category and specific OT application signatures such as Modbus and IEC.60870.5.104 . The study guide says "You can use application control signatures to detect OT protocols" and "You can filter to a specific OT protocol." That means OT application signatures are active in this sensor profile.
Option A is correct because the guide explains that application control works at different levels: "Detection of protocol (one detection per session)" and "Message level (one detection per protocol message)." It also says you can use application signatures for "granular message type identification." In the exhibit, IEC.
60870.5.104.Control.Functions is explicitly configured, which is a granular IEC message/control-level signature rather than only a protocol-level match. That means logging and control can occur at the IEC command level.
Option B is not correct because the profile shows Modbus configured at the parent protocol level as Monitor
, while the guide states that the "parent signature takes precedence over the child signature." Since protocol-level detection is one detection per session , that does not mean FortiGate will necessarily log each Modbus command individually.
Option D is incorrect because even though the broader Operational Technology category is set to block, the profile includes specific application and filter overrides for Modbus and IEC 104 behavior. So the resulting effect is not simply that all OT protocols are blocked .
NEW QUESTION # 37
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in a firewall policy, which two statements are correct? (Choose two answers)
Answer: B,D
Explanation:
The correct answers are A and C .
Option C is correct because the profile clearly contains the Operational Technology category and specific OT application signatures such as Modbus and IEC.60870.5.104 . The study guide says "You can use application control signatures to detect OT protocols" and "You can filter to a specific OT protocol." That means OT application signatures are active in this sensor profile.
Option A is correct because the guide explains that application control works at different levels: "Detection of protocol (one detection per session)" and "Message level (one detection per protocol message)." It also says you can use application signatures for "granular message type identification." In the exhibit, IEC.
60870.5.104.Control.Functions is explicitly configured, which is a granular IEC message/control-level signature rather than only a protocol-level match. That means logging and control can occur at the IEC command level.
Option B is not correct because the profile shows Modbus configured at the parent protocol level as Monitor
, while the guide states that the "parent signature takes precedence over the child signature." Since protocol-level detection is one detection per session , that does not mean FortiGate will necessarily log each Modbus command individually.
Option D is incorrect because even though the broader Operational Technology category is set to block, the profile includes specific application and filter overrides for Modbus and IEC 104 behavior. So the resulting effect is not simply that all OT protocols are blocked .
NEW QUESTION # 38
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 39
Refer to the exhibit.
An automation trigger creation wizard is shown. You want to automate some tasks in your OT network. In a FortiGate device, you create a new automation trigger based on a FortiAnalyzer event handler. When you want to configure the Event handler name field, the event handler created in FortiAnalyzer is not shown.
What are two reasons for this? (Choose two answers)
Answer: B,D
Explanation:
The correct answers are A and B .
Option B is correct because the study guide states that "When a handler generates an event with the automation stitch option enabled, FortiAnalyzer sends a notification" to FortiGate. If Automation Stitch is not enabled in the FortiAnalyzer event handler, that handler will not be usable for the FortiGate automation- stitch workflow. The guide also explains that the configuration of each event handler can include
"Automation stitches" and "Rules," showing that this is a required part of the FortiAnalyzer-to-FortiGate automation path.
Option A is also correct. The study guide explains the automation flow in the Security Fabric:
"FortiAnalyzer parses the logs and notifies the root FortiGate" and then "The root FortiGate triggers the action." That means FortiGate must have the FortiAnalyzer connection configured through the Security Fabric side before it can consume FortiAnalyzer event handlers. The warning in the exhibit about configuring a FortiAnalyzer connection also points directly to that requirement.
Option C is incorrect because + Create is not the reason the existing event handler is missing; it is only an interface control. Option D is not the best answer for this item because the question is about why the event handler name list on FortiGate is empty for FortiAnalyzer-triggered automation. The study guide's verified requirements for that workflow are the FortiAnalyzer-to-FortiGate Fabric connection and enabling Automation Stitch on the FortiAnalyzer event handler.
NEW QUESTION # 40
Refer to the exhibits.
The Playbook Monitor dashboard and the analysis of the corresponding incident analysis are shown. You created the playbook with the objective of automatically attaching the report to the incident that was created.
Which two statements are correct? (Choose two answers)
Answer: C,D
Explanation:
The correct answers are C and D .
Option D is correct because the Playbook Monitor clearly shows the starter as On_Demand and the trigger as user(admin) . The study guide states that "ON_DEMAND: The playbook runs when an administrator manually starts it" and also notes that to run it manually, you select the playbook and click Run . This exactly matches the exhibit, so the playbook was manually triggered.
Option C is also correct. The study guide explains that "tasks run one after another" and that "if needed, the output of one task can be used by the tasks that follow it." It also gives an example where workflow logic matters, such as creating an incident and then attaching details to it. In the exhibit, the sequence shown is Attach_report , then Run_report , then Create_Incident , while the incident analysis shows no report attached . Since the report must exist and the incident must already be available before it can be attached properly, the task order is wrong and must be reordered.
Option B is incorrect because the monitor shows multiple tasks completed successfully, not only Create_Incident . Option A is not the best answer because the main problem demonstrated by the exhibits is not simply waiting time, but the incorrect workflow order. The playbook completed successfully, yet the report is still not attached, which indicates a design issue in the task sequence rather than just a delay.
NEW QUESTION # 41
......
All these NSEI_OTS_AR-7.6 exam dumps formats contain real, updated, and error-free Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam questions that prepare you for the final NSEI_OTS_AR-7.6 exam. To give you an idea about the top features of NSEI_OTS_AR-7.6 Exam Dumps, a free demo download facility is being offered to Fortinet NSE I - OT Security 7.6 Architect candidates. This free NSEI_OTS_AR-7.6 exam questions demo download facility is available in all three NSEI_OTS_AR-7.6 exam dumps formats.
Braindump NSEI_OTS_AR-7.6 Free: https://www.prep4sureexam.com/NSEI_OTS_AR-7.6-dumps-torrent.html
P.S. Free & New NSEI_OTS_AR-7.6 dumps are available on Google Drive shared by Prep4sureExam: https://drive.google.com/open?id=18b-YBBHAWlnpgqRZZhMWWbYihRy_Y5O2