Moreover, we offer free Fortinet NSEI_OTS_AR-7.6 Exam Questions updates if the NSEI_OTS_AR-7.6 actual test content changes within 12 months of your buying. Our NSEI_OTS_AR-7.6 guide questions have helped many people obtain an international certificate. In this industry, our products are in a leading position in all aspects.
| Section | Objectives |
|---|---|
| Asset management | - Explain OT standard and Fortinet compliance - Implement device detection on FortiGate and FortiNAC - Fortinet Security Fabric for an OT network |
| Monitoring and risk assessment | - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers - Perform risk assessment and management |
| Network access control | - Explain OT Ethernet concepts - Configure network access authentication - Configure network segmentation schemas |
| Network security | - Configure automation - Configure security inspections for industrial protocols - Configure virtual patching |
>> Reliable NSEI_OTS_AR-7.6 Study Materials <<
You will need to pass the Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam to achieve the Fortinet NSEI_OTS_AR-7.6 certification. Due to extremely high competition, passing the Fortinet NSEI_OTS_AR-7.6 exam is not easy; however, possible. You can use DumpExam products to pass the NSEI_OTS_AR-7.6 Exam on the first attempt. The Fortinet practice exam gives you confidence and helps you understand the criteria of the testing authority and pass the Fortinet NSE I - OT Security 7.6 Architect (NSEI_OTS_AR-7.6) exam on the first attempt.
NEW QUESTION # 45
Refer to the exhibit.
A partial Application Sensor profile is shown. When you apply this profile in firewall policy, which two statements are correct? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are A and C . The study guide explains that "You can use application control signatures to detect OT protocols" and that application control provides "granular message type identification." In the exhibit, the Operational Technology application category is included in the Application Sensor profile, so OT application signatures are enabled in this profile.
Option C is also correct because the override table shows Modbus_Read.Holding.Registers = Allow and Modbus = Block . The study guide states that you can use specific granular application control signatures to allow a specific Modbus command and block all others , and it also shows that application control can identify read and write commands separately at message level. Therefore, Modbus write commands are blocked by this profile.
Option B is incorrect because the profile is not simply monitoring all OT protocols; it contains a Block action for Modbus. Option D is incorrect because the study guide links OT protocol visibility specifically to the monitor status , while in the exhibit Modbus_Read.Holding.Registers is set to Allow , not Monitor .
NEW QUESTION # 46
Refer to the exhibit.
A Virtual Patching profile is shown. You have recently updated your SCADA system and would like to apply the SCADA virtual patching profile. Which two statements about this profile are correct? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are B and D .
Option B is correct because the profile has Medium , High , and Critical selected, while Low severity is not selected. That means low-severity virtual patching signatures are not enforced by this profile. So for the device with MAC address 12:12:12:12:12 , low-severity signatures are not blocked. The study guide explains virtual patching as device-specific protection where "FortiGate caches the signatures and mitigation rules that apply to each device" and applies them when the related traffic matches the firewall policy.
Option D is correct because the Virtual Patching Exemptions table shows a row with the MAC address 11:
11:11:11:11 and no specific signature listed. The study guide states that in the Virtual Patching profile you can "Exempt a specific device with the MAC address or a specific signature." A MAC-only exemption means that specific device is excluded from virtual patching enforcement, so in practical terms it is treated as having no applicable vulnerabilities in this profile.
Option C is incorrect because the profile does not block critical signatures for all devices. The exemptions list proves that at least one device can be excluded by MAC address, and a specific signature can also be exempted. Therefore, enforcement is not universal across all devices.
Option A is incorrect because the entry Schneider.Electric.ClearSCADA.HTTP.Interface.XSS appears as a specific signature exemption , not as the only remaining vulnerability. The profile display is showing exemptions, not a statement that only one vulnerability is still present.
NEW QUESTION # 47
Refer to the exhibit.
A FortiAnalyzer report is shown.
You must extract relevant information provided by the report regarding your OT network.
Which two statements are correct? (Choose two.)
Answer: B,D
Explanation:
The correct answers are B and C . The exhibit ' s Top Threat section identifies the IPS threats as Blocked , directly confirming that the attacks were prevented rather than merely detected. The OT Traffic table also shows destination port 502 . Modbus/TCP conventionally operates on TCP port 502, and the OT Security 7.6 study guide identifies Modbus as an industrial protocol supported and inspected by Fortinet OT security controls. The report does not cover only one day; its displayed timeline spans multiple dates, from approximately October 30 through November 3. Option D is also inconsistent with the report because the visible OT destination addresses are associated with the 192.168.x.x networks rather than 10.1.5.1.
FortiAnalyzer reports summarize logged information into charts and tables specifically to expose traffic patterns, threats, and OT activity such as this.
NEW QUESTION # 48
Refer to the exhibits.
A partial Incident Analysis page and the log details related to the event are shown. An attack is reported on your OT network. You analyze the corresponding incident. Based on the information provided on the Incident Analysis page and the log details, which two statements are correct? (Choose two answers)
Answer: A,C
Explanation:
Based on the technical data provided in the exhibits and the OT Security 7.6 Architect curriculum:
* Industrial Protocol Identification (Statement A) : The log details exhibit clearly shows that the Destination Port used in the attack is 502 . According to the study guide ' s section on Industrial Protocol Protection , the standard port used by the Modbus TCP protocol is 502 . Furthermore, the attack name identifies a " Triangle.Research.Nano-10.PLC, " which are industrial controllers commonly utilizing Modbus for communications.
* Attack Mitigation (Statement B) : The log details specify that the Action taken by the FortiGate (Edge-FortiGate) was dropped . In cybersecurity and Fortinet fabric operations, dropping a packet associated with an IPS signature means the traffic was blocked from reaching its target, thereby mitigating the attack.
* Target IP Address (Statement E) : The log detail explicitly lists the Destination IP as 192.168.2.3 .
The Incident Analysis page also titles the incident with dstip:192.168.2.3. While the " Affected Endpoint " is shown as 10.1.5.20 , in an " outgoing " attack direction (as shown in the log), this likely refers to the internal source/attacker IP, whereas the target is the destination IP (192.168.2.3). Thus, Statement E is incorrect.
* Protocol Conflict (Statement C) : The IEC 104 protocol typically utilizes port 2404 . Since the log specifies port 502, Statement C is incorrect.
* Severity Distinction (Statement D) : While the Incident severity is marked as High , the question specifically asks about event severity. The " Events " table at the bottom of the Incident Analysis page shows a " User login/logout failed " event with a medium severity. Because there is a distinction in the management console between the severity of individual events and the aggregated incident, and Statement A and B are technically definitive based on port and action, A and B are the correct architectural choices.
NEW QUESTION # 49
Refer to the exhibit.
A partial OT network is shown. You have configured the FortiGate device with VLANs to segment the OT network. The supervisor now wants to connect to the PLC from the Engineering Workstation. How can you allow access from the Engineering Workstation to the PLC? (Choose one answer)
Answer: A
Explanation:
The correct answer is D. You must configure a layer 3 switch .
The study guide explains that "Layer 2 devices can add or remove tags" but "cannot modify them." It then states that "A layer 3 device, such as a router or FortiGate, can modify the VLAN tag before routing the packet. This allows them to route traffic between VLANs." It also explicitly describes
"Router on a Stick" as "a way to allow routing between VLANs." Since the exhibit shows a layer-2 switch and the Engineering Workstation and PLC are placed in different VLANs, inter-VLAN communication requires layer-3 routing.
The other options do not solve this requirement. intra-switch-policy explicit/implicit applies to a software switch , where member interfaces are in the same broadcast domain and same subnet, not to routing between separate VLANs. forward domain IDs are used in transparent mode to confine broadcasts to specific broadcast domains; they do not provide inter-VLAN access. Therefore, to let the Engineering Workstation in one VLAN reach the PLC in another VLAN, you need a layer 3 routing function , which matches option D .
NEW QUESTION # 50
......
The authority of Fortinet NSEI_OTS_AR-7.6 exam questions rests on its being high-quality and prepared according to the latest pattern. DumpExam is proud to announce that our Fortinet NSEI_OTS_AR-7.6 Exam Dumps help the desiring candidates of Fortinet NSEI_OTS_AR-7.6 certification to climb the ladder of success by grabbing the Fortinet Exam Questions.
NSEI_OTS_AR-7.6 Vce Free: https://www.dumpexam.com/NSEI_OTS_AR-7.6-valid-torrent.html