JN0-364 Study Materials | 100% Free High-quality Latest Service Provider Routing and Switching, Specialist (JNCIS-SP) Material

On the one hand, according to the statistics from the feedback of all of our customers, the pass rate among our customers who prepared for the exam with the help of our JN0-364 guide torrent has reached as high as 98%to 100%. On the other hand, the simulation test is available in our software version, which is useful for you to get accustomed to the JN0-364 Exam atmosphere. Please believe us that our JN0-364 torrent question is the best choice for you.

Juniper JN0-364 Exam Syllabus Topics:

SectionObjectives
Border Gateway Protocol (BGP)- Identify the concepts, operation, or functionality of BGP
  • 1. IBGP and EBGP functionality and interaction
  • 2. Attributes
  • 3. BGP basic operation
  • 4. BGP message types
  • 5. Route selection process
  • 6. BGP route reflection and confederations
- Demonstrate knowledge of how to configure, monitor, or troubleshoot BGP
  • 1. Troubleshooting tools
  • 2. Peers and peer groups
  • 3. Routing policy application
IPv6- Demonstrate knowledge of how to configure, monitor, or troubleshoot IPv6
- Identify the concepts, operation, or functionality of IPv6
  • 1. Dynamic routing - OSPFv3, IS-IS, BGP
  • 2. IPv6 over IPv4 tunneling
  • 3. Static routes
Intermediate System to Intermediate System (IS-IS)- Demonstrate knowledge of how to configure, monitor, or troubleshoot IS-IS
  • 1. Interfaces and adjacencies
  • 2. Troubleshooting tools
  • 3. Routing policy application
- Identify the concepts, operation, or functionality of IS-IS
  • 1. Designated intermediate system (DIS)
  • 2. Levels and areas
  • 3. Link-state database
  • 4. Type, length, values (TLVs)
  • 5. IS-IS protocol data units (PDUs)
  • 6. Adjacencies and neighbors
  • 7. Metrics
Multiprotocol Label Switching (MPLS)- Demonstrate knowledge of how to configure, monitor, or troubleshoot MPLS
  • 1. LDP-signaled Label-Switched Paths (LSPs)
  • 2. Shortest path segment-routing LSPs
  • 3. MPLS forwarding
  • 4. RSVP-signaled Label-Switched Paths (LSPs)
- Identify the concepts, operation, or functionality of MPLS CoS processing on Junos devices
  • 1. RSVP
  • 2. Labels and the label information base
  • 3. MPLS terminology
  • 4. Segment routing with MPLS
  • 5. MPLS and routing tables
  • 6. End-to-end packet flow and forwarding
  • 7. MPLS packet header
  • 8. LDP
Protocol-Independent Routing- Demonstrate knowledge of how to configure, monitor, or troubleshoot various protocol-independent routing components
  • 1. Filter-based forwarding
  • 2. Load balancing
  • 3. Static, aggregate, and generated routes
- Identify the concepts, operation, or functionality of various protocol-independent routing components
  • 1. Filter-based forwarding
  • 2. Load balancing
  • 3. Martian addresses
  • 4. Routing instances, including routing information base (RIB) (also known as routing table) group
  • 5. Static, aggregate, and generated routes
Layer 2 Bridging or VLANs- Identify the concepts, operation, or functionality of Layer 2 bridging for the Junos OS
  • 1. Provider bridging (Q-in-Q tunneling)
  • 2. Service provider switching platforms
  • 3. Frame processing
  • 4. Bridging elements and terminology
  • 5. Virtual Switches
- Identify the concepts, benefits, or functionality of VLANs
  • 1. Integrated Routing and Bridging (IRB)
  • 2. Port modes
  • 3. Tagging
- Demonstrate knowledge of how to configure, monitor, or troubleshoot Layer 2 bridging or VLANs
  • 1. IRB
  • 2. Provider bridging
  • 3. Interfaces and ports
  • 4. VLANs
Spanning Tree Protocols- Demonstrate knowledge of how to configure, monitor, or troubleshoot Spanning Tree Protocols
  • 1. STP
  • 2. RSTP
  • 3. VSTP
  • 4. MSTP
- Identify the concepts, operation, or functionality of STP
  • 1. STP
  • 2. RSTP
  • 3. VSTP
  • 4. MSTP
Open Shortest Path First (OSPF)- Demonstrate knowledge of how to configure, monitor, or troubleshoot OSPF
  • 1. Troubleshooting tools
  • 2. Routing policy application
  • 3. Interfaces and neighbor
- Identify the concepts, operation, or functionality of OSPF
  • 1. Link-state advertisement (LSA) packet type
  • 2. OSPF packet types
  • 3. Link-state database
  • 4. Router ID
  • 5. Adjacencies and neighbors
  • 6. OSPF area and router types
  • 7. Designated router and backup designated router

>> JN0-364 Study Materials <<

Latest JN0-364 Material, Certification JN0-364 Exam

Experts hired by JN0-364 exam questions not only conducted in-depth research on the prediction of test questions, but also made great breakthroughs in learning methods. With JN0-364 training materials, you can easily memorize all important points of knowledge without rigid endorsements. With JN0-364 exam torrent, you no longer need to spend money to hire a dedicated tutor to explain it to you, even if you are a rookie of the industry, you can understand everything in the materials without any obstacles. With JN0-364 Exam Questions, your teacher is no longer one person, but a large team of experts who can help you solve all the problems you have encountered in the learning process.

Juniper Service Provider Routing and Switching, Specialist (JNCIS-SP) Sample Questions (Q101-Q106):

NEW QUESTION # 101
Which two statements are correct about segment routing? (Choose two.)

Answer: A,D

Explanation:
Segment routing is a source routing paradigm that allows a source router to define the path that a packet will take through the network by assigning an ordered list of segments--identifiers that specify a forwarding path for the packet through the network. Segment Routing can be implemented over an MPLS architecture or with IPv6 (SRv6).
Segment routing does not require a full mesh of adjacencies or state per transit path in the network, which is often the case with conventional MPLS signaling protocols like RSVP-TE. It leverages the existing IGP topology for forwarding without the need to maintain a state for each LSP (Label Switched Path), hence requiring very little resources to maintain.
In segment routing, labels (or segments) are distributed via IGP routing protocols like OSPF or IS-IS with extensions to carry segment routing information. These protocols are enhanced with Segment Routing extensions to distribute labels. For example, OSPFv2 is extended with Segment Routing extensions defined in RFC 8665.


NEW QUESTION # 102
Which IS-IS packet type will establish and maintain neighbor relationships?

Answer: D

Explanation:
In theIS-IS (Intermediate System to Intermediate System)protocol, communication between routers is performed usingProtocol Data Units (PDUs). To discover neighbors and maintain adjacencies, IS-IS relies on theHello PDU (IIH - IS-IS Hello).
According to Juniper Networks technical documentation, when IS-IS is enabled on an interface, the router begins transmitting Hello PDUs to a multi-destination address (multicast). These PDUs contain essential information such as the router'sSystem ID, its configuredArea Addresses, and itsLevel capability(Level 1, Level 2, or both). For two routers to become neighbors, they must exchange these Hello PDUs and agree on specific parameters, such as the MTU of the link and the hello/hold timers.
Once an adjacency is established, the Hello PDU serves as a "keepalive" mechanism. If a router stops receiving Hello PDUs from a neighbor for a duration exceeding theHolding Time, it assumes the neighbor is down and flushes the associated Link-State PDUs (LSPs) from its database.
To clarify the other options:
* Link-State PDU (Option A):These are used to distribute actual topology and reachability information, not to form adjacencies.
* Partial Sequence Number PDU (Option C):PSNPs are used on point-to-point links to acknowledge the receipt of LSPs or to request missing LSPs.
* Update PDU (Option D):This is not a standard IS-IS term; in IS-IS, updates are handled via the flooding of LSPs.


NEW QUESTION # 103
By default, which two statements are correct about switch ports on a Junos device? (Choose two.)

Answer: B,C

Explanation:
On a Junos device, trunk ports are configured to receive and transmit tagged traffic only, while access ports are configured to receive and transmit untagged traffic.


NEW QUESTION # 104
Which two statements are correct about default BGP route propagation? (Choose two.)

Answer: B,D


NEW QUESTION # 105
Exhibit:
user@R2> show route 198.51.100.1
inet.0: 19 destinations, 19 routes (19 active, 0 holddown, 0 hidden)
Restart Complete
+ = Active Route, - = Last Active, * = Both
198.51.100.1/32 *[Static/5] 5d 21:02:26
> to 203.0.113.65 via ge-0/0/3.0
user@R2> show route 172.20.110.0/24
inet.0: 19 destinations, 19 routes (19 active, 0 holddown, 0 hidden)
Restart Complete
+ = Active Route, - = Last Active,
* = Both
172.20.110.0/24 *[Static/5] 10:43:01
> via gr-0/0/0.0
Referring to the exhibit, traffic destined to which network will be sent through the tunnel?

Answer: D

Explanation:
To determine which traffic is being sent through a tunnel in a Junos OS environment, an administrator must analyze the routing table output for the exit interface associated with each destination prefix. The provided exhibit shows the results of the show route command on routerR2for two specific destination networks.
In the first output, the destination198.51.100.1/32is an active static route. The next-hop information specifies that traffic for this address is sent to the gateway 203.0.113.65 via the interfacege-0/0/3.0. According to Juniper Networks interface naming conventions, the prefixge-denotes aGigabit Ethernetinterface, which represents a standard physical connection. Therefore, this traffic does not traverse a tunnel.
In the second output, the destination172.20.110.0/24is also an active static route. However, the next-hop for this network is listed asvia gr-0/0/0.0. In the Junos operating system, thegr-prefix explicitly identifies a Generic Routing Encapsulation (GRE) tunnel interface. GRE is a widely used protocol in service provider networks to encapsulate various network layer protocols over an IP backbone, effectively creating a virtual point-to-point link. Because the routing table has installed the route for 172.20.110.0/24 specifically via the gr- interface, all traffic destined for this network will be encapsulated and sent through the tunnel.
The other choices are incorrect for the following reasons:
* 203.0.113.65 (Option B):This is the next-hop IP address for the physical Gigabit Ethernet path; it is not a destination network directed to a tunnel.
* 0.0.0.0/0 (Option C):There is no information in the exhibit regarding a default route.
* 198.51.100.1/32 (Option D):As identified by thege-interface prefix in the exhibit, traffic for this destination is sent via a physical Ethernet link.


NEW QUESTION # 106
......

Rather than pretentious help for customers, our after-seals services on our JN0-364 exam questions are authentic and faithful. Many clients cannot stop praising us in this aspect and become regular customer for good on our JN0-364 Study Guide. We have strict criterion to help you with the standard of our JN0-364 training materials. Our company has also being Customer First. So we consider the facts of your interest firstly.

Latest JN0-364 Material: https://www.testkingpdf.com/JN0-364-testking-pdf-torrent.html