As we all know, the NSEI_OTS_AR-7.6 certificate has a very high reputation in the global market and has a great influence. But how to get the certificate has become a headache for many people. Our NSEI_OTS_AR-7.6learning materials provide you with an opportunity. Once you choose our NSEI_OTS_AR-7.6 Exam Practice, we will do our best to provide you with a full range of thoughtful services. Whenever you have questions about our NSEI_OTS_AR-7.6 study guide, our service will give you the most professional advice.
| Section | Objectives |
|---|---|
| Topic 1: Monitoring and Risk Assessment | - Perform risk assessment and management - Analyze security reports from FortiAnalyzer - Create FortiAnalyzer event handlers |
| Topic 2: Network Security | - Configure virtual patching - Configure automation - Configure security inspections for industrial protocols |
| Topic 3: Network Access Control | - Configure network access authentication - Explain OT Ethernet concepts - Configure network segmentation schemas |
| Topic 4: Asset Management | - Explain OT standards and Fortinet compliance - Use Fortinet Security Fabric for an OT network - Implement device detection on FortiGate and FortiNAC |
>> New NSEI_OTS_AR-7.6 Test Sims <<
Our experts have carefully researched each part of the test syllabus of the NSEI_OTS_AR-7.6 guide materials. Then they compile new questions and answers of the study materials according to the new knowledge parts. At last, they reorganize the NSEI_OTS_AR-7.6 learning questions and issue the new version of the study materials. Once the newest test syllabus of the NSEI_OTS_AR-7.6 Exam appear on the official website, our staff will quickly analyze them and send you the updated version. So our NSEI_OTS_AR-7.6 guide materials deserve your investment.
NEW QUESTION # 38
In the Purdue model, at which level are physical assets like the Industrial Internet of Things (IIoT) placed?
(Choose one answer)
Answer: C
Explanation:
According to the OT Security 7.6 Architect study guide regarding the Purdue Model :
* Asset Location : The study guide states that " All critical physical assets are located on the plant floor and equipped with IIoT sensors. "
* Level Classification : The " plant floor " is further defined as the " control area zone, " which consists of Levels 0, 1, and 2 .
* Hierarchy : The " Operations & Control " zone is identified as Level 3 and Level 3.5 .
* Direct Answer : In the " Introduction " lesson ' s Knowledge Check , the specific question " In the Purdue model, at which level are IIoTs placed? " is provided with the verified answer: Below Level 3.5 .
NEW QUESTION # 39
Refer to the exhibit.
The OT devices behind the ruggedized FortiGate have vulnerabilities and you want to apply a virtual patching profile in the firewall policy. Why is Virtual Patching not available in the Security Profiles section? (Choose one answer)
Answer: A
Explanation:
The correct answer is A. You must enable Virtual Patching in the Feature Visibility section .
The study guide states clearly that "By default, virtual patching profiles are hidden on the GUI, and you must enable them through System > Feature Visibility." That exactly matches the situation in the exhibit, where Virtual Patching does not appear under Security Profiles . So the issue is not that the feature is unsupported, but that it is simply hidden in the GUI until it is enabled.
The other options do not answer the question being asked. A valid OT security service license is required for virtual patching signatures and protection workflow, and OT signatures are relevant to IPS-based OT protection, but those do not explain why the menu item itself is missing from the Security Profiles section .
The guide specifically identifies Feature Visibility as the reason the Virtual Patching profile is not shown in the GUI. Therefore, the required action is to enable Virtual Patching in System > Feature Visibility .
NEW QUESTION # 40
Refer to the exhibit.
A Run_report task is shown. You want to automate the generation of a newly created report on FortiAnalyzer . When you configure the Run_report task in Playbook, why is the report not shown in the Report field? (Choose two answers)
Answer: B,D
Explanation:
Based on the architecture of FortiAnalyzer within the Security Fabric and its automation capabilities:
* Automation Stitch and Reports : Within the Security Fabric environment, FortiAnalyzer serves as a key element in creating automation stitches and playbooks. For a report to be selectable within a Playbook task (such as the Run_report task shown in the exhibit), it must meet specific technical prerequisites in the report configuration.
* Auto-cache Requirement (Answer C) : For a report to be used for automated generation, it must be " ready " to be processed by the engine without manual intervention. Auto-cache must be enabled in the report settings to ensure the report can be generated dynamically and efficiently when triggered by the playbook.
* Extended Log Filtering (Answer B) : Playbooks often pass specific variables from the trigger (such as a specific device IP or a time range) into the report. For the report to accept these dynamic parameters and be visible as an " automation-compatible " report in the Playbook interface, Extended Log Filtering must be enabled.
* Workflow Constraints : Without these two settings enabled on the report itself, the Playbook engine cannot guarantee the report ' s successful generation or parameter injection, and thus filters it out of the available selection list in the Run_report task.
NEW QUESTION # 41
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 42
Refer to the exhibit.
A firewall policy page is shown. To improve the security of your OT network, you have configured a Supervisor profile in the firewall policies, as shown in the exhibit. However, a supervisor is reporting that he cannot ping PLC-1. What are the two reasons? (Choose two answers)
Answer: A,D
Explanation:
The correct answers are A and C .
Option A is correct because the study guide explains that with active authentication , FortiGate prompts the user only when they use "an acceptable login protocol." It states: "When you use only active authentication, if all possible policies that could match the source IP address have authentication enabled, then the user will receive a login prompt (assuming they use an acceptable login protocol)." A direct ping to PLC-1 uses ICMP , which is not the kind of login protocol used to trigger user authentication.
So the supervisor must first authenticate through a protocol such as HTTPS or Telnet , then the ICMP traffic can match the authenticated policy.
Option C is also correct because the exhibit shows policy ID 8 greyed out, meaning it is not enabled. That policy appears above the Supervisor_access (9) policy and allows broader access to PLC-1 , whereas policy 9 is limited to ALL_ICMP . The study guide explains that "Because the user has not yet authenticated, the user group aspect of the traffic does not match" and FortiGate continues searching for another complete match. In this case, with policy 8 disabled, the supervisor is left with only the ICMP rule, which cannot be used to perform the initial login step needed for active authentication.
Option B is not supported by the exhibit. Option D is incorrect because auth-on-demand always would force authentication prompts more aggressively, but the core problem here is that the user is trying to start with ICMP and the broader policy that could permit the initial authenticated access is disabled.
NEW QUESTION # 43
......
Prep4pass not only provide the products which have high quality to each candidate, but also provides a comprehensive after-sales service. If you are using our NSEI_OTS_AR-7.6 products, we will let you enjoy one year of free updates. So that you can get the latest exam information in time. We will be use the greatest efficiency to service each candidate.
Knowledge NSEI_OTS_AR-7.6 Points: https://www.prep4pass.com/NSEI_OTS_AR-7.6_exam-braindumps.html