The web-based Designing Cisco Wireless Networks (300-110) practice exam is accessible from any major OS, including Mac OS X, Linux, Android, Windows, or iOS. These Cisco 300-110 exam questions are browser-based, so there's no need to install anything on your computer. Chrome, IE, Firefox, and Opera all support this Cisco 300-110 web-based practice exam. You can take this Designing Cisco Wireless Networks (300-110) practice exam without plugins and software installation.
| Section | Weight | Objectives |
|---|---|---|
| Topic 1: WLAN High Availability and Security Design | 20% | - High availability design
- Security architecture design
|
| Topic 2: Mobility Design | 25% | - Roaming optimization
- Mobility architecture models
|
| Topic 3: Wireless Site Survey | 25% | - Design requirements collection and constraint evaluation
- RF propagation and attenuation analysis - Pre-deployment survey and validation |
| Topic 4: Wireless Infrastructure Design | 30% | - Wired-wireless integration design
|
>> Practice 300-110 Test Online <<
The content of our 300-110 practice engine is based on real exam by whittling down superfluous knowledge without delinquent mistakes rather than dropping out of reality. Being subjected to harsh tests of market, our 300-110 exam questions are highly the manifestation of responsibility carrying out the tenets of customer oriented. And our 300-110 Study Materials are warmly praised and welcomed by the customers all over the world.
NEW QUESTION # 60
A customer is building a new warehouse facility that has only its foundation and perimeter walls built. The building will be complete in the next eight months. The customer needs a detailed bill of materials and costs for a wireless network that must support RF scanners throughout the warehouse. How should the survey be performed?
Answer: B
Explanation:
A predictive survey (also called a virtual or model-based survey) is the appropriate and only feasible methodology for a facility that does not yet physically exist in its complete form. Since the warehouse has only its foundation and perimeter walls, it is impossible to conduct any form of physical (active or passive) survey of the complete environment. A predictive survey uses architectural floor plans imported into a tool such as Ekahau Site Survey, where the engineer defines attenuation areas representing planned materials and structures: concrete block walls, steel shelving racks, metallic surfaces, and other warehouse-specific obstructions. The software models RF propagation through these defined attenuation values, enabling accurate AP placement planning, antenna selection, and channel planning without physical access to the complete facility. The output is a validated bill of materials with AP counts, models, and associated infrastructure requirements. Passive surveys (Options A and C) require physical APs transmitting RF signals to collect measurement data - impossible in an incomplete building. A hybrid approach mixing passive survey with predictive modeling introduces measurement errors from the incomplete physical state. Reference: WLSD Study Guide - Survey Types, Predictive Survey Methodology, Pre-Deployment Planning for New Construction.
NEW QUESTION # 61
A consultant must design a WLAN for a large campus with high AP density, 50-100 clients per cell, 5 Mbps throughput per client minimum, 5 GHz and 2.4 GHz coverage at -67 dBm, and no 802.11b clients. Which two WLAN design approaches meet the requirements? (Choose two.)
Answer: A,E
Explanation:
Designing for 50-100 clients per cell with 5 Mbps minimum throughput and no 802.11b clients requires two critical optimizations. First, setting minimum mandatory data rates to 12-18 Mbps (Option A) removes legacy lower data rates from the AP ' s supported rate set. When 1, 2, 5.5, and 11 Mbps rates are disabled and 12 Mbps becomes the minimum mandatory rate, legacy 802.11b clients are excluded from the cell, airtime efficiency improves dramatically, and clients connecting at higher rates use less channel time per frame, increasing effective capacity. Second, Flexible Radio Assignment (FRA) for 2.4 GHz reduction (Option D) is critical in high-density environments. FRA allows the WLC to dynamically reassign some 2.4 GHz radios to 5 GHz operation or monitor mode, reducing 2.4 GHz cell size and interference while increasing 5 GHz capacity in the high-density area. Option C directly contradicts the no-802.11b requirement. Option B (6 SSIDs per AP) is a management consideration but does not directly address throughput. Option E (80-160 MHz channels) would consume available spectrum, reducing the number of usable non-overlapping channels and worsening co-channel interference at high density. Reference: WLSD Study Guide - High-Density WLAN Design, Minimum Data Rate Configuration, Flexible Radio Assignment (FRA).
NEW QUESTION # 62
An engineer is estimating the loss between two floors of an office building. Using Ekahau, they have measured -45 dBm at the ground level of the floor with the access point and -50 dBm at the ceiling level of the floor below it. Which value is the loss of the floor?
Answer: A
Explanation:
Floor loss calculation is a fundamental skill in multi-floor wireless site survey methodology. The floor attenuation value represents the signal power reduction caused by penetrating through a single floor structure including the floor decking, subfloor, ceiling material, plenum space, and any structural elements. In this measurement scenario, the engineer has two data points: -45 dBm measured at the ground level of the floor containing the access point (the signal level just below the AP ' s floor) and -50 dBm measured at the ceiling level of the floor below (the signal level just after passing through the floor structure). The floor loss is simply the difference between these two measurements: (-45 dBm) - (-50 dBm) = -45 + 50 = 5 dB. The result is expressed as a positive value (5 dB) representing attenuation - signal power decreases by 5 dB when passing through the floor. Expressing it as -5 dB (Option B) would incorrectly imply a signal gain. The 95 dB values (Options A and D) result from incorrectly adding rather than subtracting the dBm values - a common error when working with negative dBm figures. This floor attenuation value (5 dB) would then be entered into Ekahau ' s floor material properties to improve predictive model accuracy. Reference: WLSD Study Guide - Multi-Floor Signal Propagation, Floor Attenuation Factor (FAF), Ekahau Floor Loss Measurement Methodology.
NEW QUESTION # 63
A customer is building a new warehouse facility that has only its foundation and perimeter walls built. The building will be complete in the next eight months. The customer needs a detailed bill of materials and costs for a wireless network that must support RF scanners throughout the warehouse.
How should the survey be performed?
Answer: B
Explanation:
A predictive survey (also called a virtual or model-based survey) is the appropriate and only feasible methodology for a facility that does not yet physically exist in its complete form. Since the warehouse has only its foundation and perimeter walls, it is impossible to conduct any form of physical (active or passive) survey of the complete environment. A predictive survey uses architectural floor plans imported into a tool such as Ekahau Site Survey, where the engineer defines attenuation areas representing planned materials and structures: concrete block walls, steel shelving racks, metallic surfaces, and other warehouse-specific obstructions. The software models RF propagation through these defined attenuation values, enabling accurate AP placement planning, antenna selection, and channel planning without physical access to the complete facility. The output is a validated bill of materials with AP counts, models, and associated infrastructure requirements.
NEW QUESTION # 64
A customer has multiple WLCs running in N+1 redundancy with APs load balanced between the WLCs. The customer performs AP failover testing between the WLCs and notices that some of the APs do not move back to their primary WLC after it recovers. What are two points that must be addressed in the design? (Choose two.)
Answer: B,D
Explanation:
In an N+1 redundancy deployment, an AP ' s ability to return to its designated primary WLC after that controller recovers depends on two distinct configuration requirements working in concert. First, the AP Fallback feature (Option C) must be enabled on the WLC. AP Fallback instructs APs to monitor the availability of their configured primary controller and automatically reconnect to it when it becomes available again, rather than remaining permanently joined to the N+1 backup controller. Without AP Fallback enabled, APs stay connected to whichever controller they most recently joined. Second, the APs must have their primary WLC information correctly configured (Option D). If an AP does not have the primary controller ' s name, IP address, or FQDN correctly set, it cannot identify when its designated primary has recovered and therefore cannot initiate a return fallback. DHCP Option 43 (Option A) is used for initial AP discovery only.
Secondary WLC configuration (Option B) addresses failover direction but not the return path. AP failover priority (Option E) controls which APs are moved first during a failover event, not whether fallback occurs.
Reference: WLSD Study Guide - N+1 Redundancy Design, AP Fallback Configuration, Controller Primary, Secondary and Tertiary Assignment.
NEW QUESTION # 65
......
The pressure we face comes from all aspects. As the social situation changes, these pressures will only increase. We cannot change the external environment. What we can do is improve our own strength. However, blindly taking measures may have the opposite effect. So here comes your best assistant-our 300-110 Practice Engine. If you study with our 300-110 exam materials, you can become better no only because that you can learn more, but also because you can get the admired 300-110 certification.
300-110 Reliable Exam Practice: https://www.actual4dumps.com/300-110-study-material.html